保麗龍雕刻機在使用過程中出現的

2023年07月20日 07:12:38人氣：102來源：山東墨源數控設備有限公司

保麗龍雕刻機不能正常工作時，一般是由以下原因造成的，操作者可以根據實際情況來判斷和解決。

When the styrofoam engraving machine can not work normally, it is generally caused by the following reasons, the operator can judge and solve according to the actual situation.

(1)保麗龍雕刻機三軸中有一軸不能動，此時要檢查一下相應全順保麗龍雕刻機軸所對應的驅動塊是否損壞。檢查方法可使用替換法：將全順保麗龍雕刻機不動軸所對應的航空插頭拔下插在其他能動軸所對應的驅動上。

(1) One of the three axes of the styrofoam engraving machine is not active. At this time, it is necessary to check whether the drive block corresponding to the axis of the styrofoam engraving machine is damaged. The inspection method can be replaced: pull out the aviation plug corresponding to the fixed shaft of Quanshun styrofoam engraving machine and plug it into the corresponding drive of other active shafts.

保麗龍雕刻機

(2)保麗龍雕刻機如果交換后不動軸走動正常，則可說明該軸所對應的驅動塊已損壞，需要更換好驅動塊。如果不動軸還是不行就說明電纜線或電機有故障更換電纜線或者電機。三軸均不能動。此時檢查一下三軸航空插頭是否已和控制箱連接好，控制箱電源是否已打開。數據線是否和控制箱和電腦主機中控制卡連接好。如果以上都正常，則請和全順保麗龍雕刻機維修點聯系。

(2) If the fixed shaft moves normally after exchanging, it indicates that the drive block corresponding to the shaft is damaged and needs to be replaced. If the shaft still does not move, it means that the cable or motor is faulty, replace the cable or motor. All three axes can't move. At this time, check whether the three-axis aviation plug has been connected with the control box, and whether the power supply of the control box has been turned on. Whether the data line is well connected with the control card in the control box and computer host. If the above is normal, please contact Quanshun Baolilong engraving machine authorized maintenance point.

(3)保麗龍雕刻機主軸不能正常運轉。首先檢查變頻器LED顯示屏顯示的錯誤代碼(參見全順保麗龍雕刻機變頻器說明書錯誤代碼項)

(3) The main shaft of styrofoam engraving machine can not work normally. First, check the error code displayed on the inverter LED display screen (refer to the error code item in the frequency converter Manual of Quanshun Baolilong engraving machine)

主軸電機全順保麗龍雕刻機常見故障和處理：

Common faults and treatment of main shaft motor Quanshun Baolilong engraving machine:

保麗龍雕刻機電機發燙檢查水泵是否工作循環水是否正常，電機沒勁檢查電機線是否缺相電纜是否短路，電機聲音異常電機是否超負荷運轉電機內部故障，電機反轉檢查電機線是否缺相將輸出UVW端任意調換兩端。

The motor of styrofoam engraving machine is hot, check whether the water pump works, whether the circulating water is normal, whether the motor is weak, whether the motor line is short circuited, whether the motor sound is abnormal, whether the motor is overloaded, whether the internal fault of the motor, the motor reverses to check whether the motor line is lack of phase, and the output UVW end will be randomly exchanged at both ends.

關鍵詞：雕刻機變頻器

上一篇：木工雕刻機驅動器和水冷電機出現故障及解決方法

下一篇：鍋爐除垢劑使用方法及注意事項

全年征稿/資訊合作 聯系郵箱：1271141964@qq.com

免責聲明

凡本網注明"來源：智能制造網"的所有作品，版權均屬于智能制造網，轉載請必須注明智能制造網，http://towegas.com。違反者本網將追究相關法律責任。
企業發布的公司新聞、技術文章、資料下載等內容，如涉及侵權、違規遭投訴的，一律由發布企業自行承擔責任，本網有權刪除內容并追溯責任。
本網轉載并注明自其它來源的作品，目的在于傳遞更多信息，并不代表本網贊同其觀點或證實其內容的真實性，不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時，必須保留本網注明的作品來源，并自負版權等法律責任。
如涉及作品內容、版權等問題，請?jiān)谧髌钒l(fā)表之日起一周內與本網聯系，否則視為放棄相關權利。

国产强伦姧在线观看无码,中文字幕99久久亚洲精品,国产精品乱码在线观看,色桃花亚洲天堂视频久久,日韩精品无码观看视频免费

保麗龍雕刻機在使用過程中出現的

免責聲明