智能制造網APP
智能制造網手機站
智能制造網小程序
智能制造網官微
智能制造網服務號
直播推薦
回放
回放
企業動態
- 上汽集團、智己汽車走訪易格斯：共探工程塑料創新應用與汽車產業升級
- 園區網絡難不難，華為F5G-A有新招
- 力安科技受邀參加2025養老機構+物業消防安全管理創新論壇
- 以光惠算，一場圍繞園區網的“生產力”革命
- 無光，不AI，如何抓住F5G-A萬兆全光園區的百億商機？
- 電解鋁行業智能化轉型再加速！廣域銘島全廠智能決策中樞正式啟用
- 京東工業持續強化拓品增商 2025合作伙伴大會走進廣州
- 電池隔爆高低溫試驗箱：新能源安全測試的“守護者”
推薦展會
1.軸承選用C級高速角觸摸軸承本產品NSK軸承。
1. Class C high-speed angle touch bearing is selected as the bearing. NSK bearing of this product.
2.選用精度鋼球堅持器，這樣確保了電主軸在高速磨削時的反轉精度。
2. The precision steel ball holder is selected to ensure the reverse accuracy of the motorized spindle during high-speed grinding.
3.電主軸外殼冷卻選用液循環冷卻，降低高速旋轉引起的發熱溫升。
3. The motorized spindle shell is cooled by circulating coolant to reduce the heating temperature rise caused by high-speed rotation.
4.電主軸選用油霧光滑，選用油脂光滑。
4. The motorized spindle shall be smooth with oil mist and grease.
運用方法
Application method
1.開機前有必要接上油水管，做到電主軸先接通油水管后再發動主軸電機，安裝時水管油管不能接錯。主軸左右兩頭為水管，中間為油管(數控鉆銑床主軸是油脂光滑，不選用以上方法。)
1. Before startup, it is necessary to connect the oil water pipe, so that the motorized spindle can be connected with the oil water pipe first, and then start the spindle motor. During installation, the water pipe and oil pipe can not be connected incorrectly. The left and right ends of the spindle are water pipes and the middle is oil pipes (the spindle of NC drilling and milling machine is smooth with grease, so the above method is not selected.)
2.運用電主軸時應先接油霧管點，管點接頭應清潔凈，防止污物進入形成軸承燒壞。操作時應看電主軸前端部稍有油霧泄出后，才干發動電主軸，油霧光滑主張選用5號主軸油調理，進油管為20-30滴/分，常常查看不能斷油，不然會形成主軸損壞。
2. When using the motorized spindle, the oil mist pipe point shall be connected first, and the pipe point joint shall be clean to prevent dirt from entering and burning the bearing. During operation, the motorized spindle can be started only after the oil mist at the front end of the motorized spindle leaks out slightly. The oil mist is smooth. It is recommended to use No. 5 spindle oil for conditioning. The oil inlet pipe is 20-30 drops / min. it is often checked that the oil cannot be cut off, otherwise the spindle will be damaged.
3.操作時，有必要做到主軸停止轉動后，才封閉油霧，這樣才干延長運用壽命，說明發動不宜過火頻頻。
3. During operation, it is necessary to close the oil mist after the main shaft completely stops rotating, so as to prolong the service life, indicating that the engine should not be started too frequently.
4.電主軸運用前有必要查看砂輪接桿是否同軸，如不同軸超過0.03毫米應還砂輪接桿，不然既損壞電主軸，又磨欠好作業，磨削時應留意不要碰擊，應校正后再進去磨削。
4. Before using the motorized spindle, it is necessary to check whether the grinding wheel connecting rod is coaxial. If it is not coaxial more than 0.03mm, return the grinding wheel connecting rod, otherwise the motorized spindle will be damaged and the grinding operation will not be good. During grinding, pay attention not to bump, and go in for grinding after correction.
維修保養
Maintenance
1.電主軸所接中頻電源額外電壓，頻率應與電主軸技術參數相符，電主軸轉速能夠改動頻率來調正，一起電壓也成正比改動。
1. The frequency of the additional voltage of the medium frequency power supply connected to the motorized spindle shall be consistent with the technical parameters of the motorized spindle. The speed of the motorized spindle can be adjusted by changing the frequency, and the voltage is also changed in direct proportion.
2.運用過程中應防止電主軸軸端部與工件發生意外碰擊。
2. During operation, the end of the motorized spindle shaft shall be prevented from accidental collision with the workpiece.
3.運用過的電主軸暫不必，使用壓縮空氣吹清水管內冷卻液，避免生銹，阻塞小孔。并在外表涂上防銹油、軸端加保護裝置放于干燥處保存。
3. The used motorized spindle is not necessary temporarily. Use compressed air to blow the coolant in the clean water pipe to avoid rust and blocking the small hole. The surface shall be coated with anti rust oil, and the shaft end shall be protected and stored in a dry place.
4.應盡量削減空工作，開機前應查看進出冷卻水石非疏通。
4. Empty work shall be reduced as far as possible, and the inlet and outlet cooling water shall be checked before startup.
關鍵詞：中頻電源
全年征稿/資訊合作
聯系郵箱：1271141964@qq.com
免責聲明
- 凡本網注明"來源：智能制造網"的所有作品，版權均屬于智能制造網，轉載請必須注明智能制造網，http://towegas.com。違反者本網將追究相關法律責任。
- 企業發布的公司新聞、技術文章、資料下載等內容，如涉及侵權、違規遭投訴的，一律由發布企業自行承擔責任，本網有權刪除內容并追溯責任。
- 本網轉載并注明自其它來源的作品，目的在于傳遞更多信息，并不代表本網贊同其觀點或證實其內容的真實性，不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時，必須保留本網注明的作品來源，并自負版權等法律責任。
- 如涉及作品內容、版權等問題，請?jiān)谧髌钒l(fā)表之日起一周內與本網聯系，否則視為放棄相關權利。
浙公網安備 33010602000006號
智能制造網APP
智能制造網小程序
微信公眾號
SAMPE中國第二十屆國際先進復合材料展覽會
展會城市：北京市展會時間：2025-06-18