雕刻機的干擾問題怎么解決？

2023年07月16日 07:13:21人氣：108來源：山東墨源數控設備有限公司

經過我們的技術團隊分析，發現是由于一般步進電機和驅動器外殼未采用鋁、鈦、鎂合金外殼進行磁屏蔽，對高靈敏的接收機系統造成干擾，使其無法工作，并且污染電源，造成雕刻機控制系統的單片機和上位機無法進行通訊，嚴重者造成單片機死機，給正常使用造成了困難，因此干擾問題必須加以解決。

Through the analysis of our technical team, we found that the general stepper motor and driver Shell did not use aluminum, titanium, magnesium alloy shell for magnetic shielding, which caused interference to the highly sensitive receiver system, made it unable to work, and polluted the power supply, resulting in the engraving machine control system's single-chip microcomputer and upper computer unable to communicate, and even caused the single-chip microcomputer crash, It is difficult for normal use, so the interference problem must be solved.

一、加裝電源濾波器，減少對交流電源的污染。

1、 Add power filter to reduce the pollution of AC power supply.

將電源濾波器的地、驅動器PE（驅動器與機箱底板絕緣）、控制脈沖PULSE-方向脈沖DIR-短接后的引出線、電機接地線、驅動器與電機之間電纜防護套、驅動器屏蔽線均接到機箱壁上的接地柱上，要求接觸良好。

Connect the ground of power filter, PE of driver (insulation between driver and chassis bottom plate), outgoing line of control pulse direction pulse dir short circuit, motor ground wire, cable protective sleeve between driver and motor, driver shield wire to the grounding post on chassis wall, and ensure good contact.

二、盡量加大控制線與電源線（L、N）、電機驅動線（U、V、W）之間的距離，避免交叉.比如我們?cè)谔幚黼p軸驅動系統中兩個處在同一機箱的驅動器安裝位置時,木工雕刻機一個驅動器銘牌朝前，另一個則朝后，并在結構布置上使這些引線盡量短。

2、 Try to increase the distance between the control line and the power line (L, n), motor drive line (U, V, w) to avoid crossing. For example, when we deal with the installation position of two drivers in the same chassis in the dual axis drive system, one driver's name plate of woodworking engraving machine is facing forward, the other is facing backward, and these leads should be as short as possible in the structural arrangement.

三、使用屏蔽線減輕外界對自己的干擾，或自己（電源線）對外界的干擾。

3、 Use the shielded wire to reduce the interference from the outside world, or from the outside world.

更多石材雕刻機整機和石材雕刻機配件和配套服務，請關注我們石材雕刻機廠家了解。

More stone carving machine and stone carving machine accessories and supporting services, please pay attention to our official website of stone carving machine manufacturers.

關鍵詞：步進電機驅動器雕刻機控制系統單片機

上一篇：加速度傳感器的誤差分析和修正方法

下一篇：梳棉機：工作原理、應用與維護

全年征稿/資訊合作 聯系郵箱：1271141964@qq.com

免責聲明

凡本網注明"來源：智能制造網"的所有作品，版權均屬于智能制造網，轉載請必須注明智能制造網，http://towegas.com。違反者本網將追究相關法律責任。
企業發布的公司新聞、技術文章、資料下載等內容，如涉及侵權、違規遭投訴的，一律由發布企業自行承擔責任，本網有權刪除內容并追溯責任。
本網轉載并注明自其它來源的作品，目的在于傳遞更多信息，并不代表本網贊同其觀點或證實其內容的真實性，不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時，必須保留本網注明的作品來源，并自負版權等法律責任。
如涉及作品內容、版權等問題，請?jiān)谧髌钒l(fā)表之日起一周內與本網聯系，否則視為放棄相關權利。

国产强伦姧在线观看无码,中文字幕99久久亚洲精品,国产精品乱码在线观看,色桃花亚洲天堂视频久久,日韩精品无码观看视频免费

雕刻機的干擾問題怎么解決？

免責聲明

雕刻機的干擾問題怎么解決？