ARCH電源應用資料

2009年03月09日 19:41:34人氣：2906來源：西安浩南電子科技有限公司

[ Application Note ]

AC-DC Application Note

AC Input Line Connection :
	The pin of AC line （L）, ac neutral （N）,the third wire safety ground （FG） should be retained from the AC power outlet to the power supply input terminals without accidental interchange. （Figure 1.1）
	（Figure 1.1）
	The FG pin should be connected to the equipment where power supply is placed as thickershorter to protect electric shock or noise interference. （Figure 1.2）
	（Figure 1.2）

Fuse :
	To add a fuse at the input terminals of the power supply to provide safetyprotection. We suggest using a 1. slow blow fuse for our AC-DC Converters including AHC, APC, ATC, ANCASC series. （Figure 2.1）
	（Figure 2.1）

Seriesparallel operation :
	I. Series operation Most power converters can be operated in series if they have overload limitation by either constant current or constant power circuits. To protect each output from the reverse voltage applied by the other unit in the event of load short circuits, reverse biased diodes are used as shown in Figure 3.1
	（Figure 3.1）
	II. Parallel operation This is only recommended with power converters specifically designed for parallel connection. In the parallel redundant scheme illustrated in Figure 3.2 one of the power converters could be replaced by a battery followed by a DC-DC converter to provide a no-break power system in the event of main supply failure.
	（Figure 3.2）

Reduce the output ripplenoise :
	Please be aware the length of screw should not be longer than 3 mm while you mounting/ adopting our power supply on your end application, in case screw break through Mylar or PCB Board result in short circuit.
	（Figure 4.1）

Screws for Switching Power Supply （AQS & AQF Series） :
	Please be aware the length of screw should not be longer than 3 mm while you mounting/ adopting our power supply on your end application, in case screw break through Mylar or PCB Board result in short circuit.

DC-DC Application Note

Connection for standard use :
	Cin: External capacitor on the input side Co: External capacitor on the output side

Reverse input voltage protection :
	Avoid the reverse input voltage because it will damage the power supply. Installing an external diode can protect the converter from the reverse input voltage.

Seriesparallel operation :
	I. Series operation Most power converters can be operated in series if they have overload limitation by either constant current or constant power circuits. To protect each output from the reverse voltage applied by the other unit in the event of load short circuits, reverse biased diodes are used as shown in Figure 3.1
	（Figure 3.1）
	II. Parallel operation This is only recommended with power converters specifically designed for parallel connection. In the parallel redundant scheme illustrated in Figure 3.2 one of the power converters could be replaced by a battery followed by a DC-DC converter to provide a no-break power system in the event of main supply failure.
	（Figure 3.2）

Remote On/ Off Control Pin :
	Positive logic remote on/ off turns the module on during a logic high voltage on the remote on/ off pin,off during a logic voltage low. In order to turn module on or off, the use must supply a switch to control the voltage between the on / off terminalthe –Vin terminal.

AC-DC Application Note:

DC-DC Application Note:

全年征稿/資訊合作 聯系郵箱：1271141964@qq.com

凡本網注明"來源：智能制造網"的所有作品，版權均屬于智能制造網，轉載請必須注明智能制造網，http://towegas.com。違反者本網將追究相關法律責任。
企業發布的公司新聞、技術文章、資料下載等內容，如涉及侵權、違規遭投訴的，一律由發布企業自行承擔責任，本網有權刪除內容并追溯責任。
本網轉載并注明自其它來源的作品，目的在于傳遞更多信息，并不代表本網贊同其觀點或證實其內容的真實性，不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時，必須保留本網注明的作品來源，并自負版權等法律責任。
如涉及作品內容、版權等問題，請在作品發表之日起一周內與本網聯系，否則視為放棄相關權利。

国产强伦姧在线观看无码,中文字幕99久久亚洲精品,国产精品乱码在线观看,色桃花亚洲天堂视频久久,日韩精品无码观看视频免费