EMERSON XVM-403-TBNS-0000驅動通信接口模塊
1.產 品 詳 情 資 料：
主要功能?提供一個ControlNet端口（位于TP865基板上的BNC連接器）。?簡單的DIN導軌安裝。?處理多達31個分布式I/O節點的I/O掃描。?安裝在機組底座中的預設兩個字母的阿爾法代碼鎖定裝置可防止安裝不兼容的組件。?支持熱插拔。說明CI865/TP865將ControlNet連接到AC 800M。該模塊可以將舊的Satt I/O系統（機架I/O和200系列I/O）與AC 800M控制器平臺一起使用，但不能用作通用ControlNet接口。TP865基板有一個用于連接I/O機架的BNC連接器。底板有一個代碼鎖，見第75頁表4，可防止在TP865基板上安裝不正確類型的裝置。CI865擴展單元包含CEX總線邏輯、ControlNet總線邏輯、CPU和DC/DC轉換器，該轉換器通過CEX總線從+24 V電源提供適當?shù)碾妷骸（un）或F（ault）LED均亮起。CI865單元正在配置中。請留出時間以便最終確定。如果情況依然存在，并且CEX總線上的其他單元指示燈未點亮：?檢查PM8xx處理器單元內的CEX總線保險絲?啟動來自PM8xx處理單元的復位信號（INIT）?更換CI865單元F（故障）指示燈亮起CI865單元正在重新啟動過程中。請留出時間以便最終確定。如果情況依然存在，請更換單元。COM A/COM B LED熄滅電源關閉或重置模式COM A/COM B LED呈綠色穩定通道正常COM A/COM乙LED呈綠色閃爍臨時錯誤或需要初始設置COM A/COM丙LED呈紅色穩定模塊損壞，必須更換COM A/COM丁LED呈紅色閃爍壞通道電纜
Key Features ? Provides one ControlNet port, (a BNC connector located on the TP865 Baseplate). ? Simple DIN-rail mounting. ? Handles I/O scanning of up to 31 distributed I/O nodes. ? Pre-set, two-letter Alpha code locking device installed in unit base prevents mounting of incompatible components. ? Supports Hot swap. Description The CI865/TP865 connects ControlNet to AC 800M. The module makes it possible to use older Satt I/O system (Rack I/O and Series 200 I/O) with the AC 800M controller platform but it can not be used as a general ControlNet interface. The TP865 Baseplate has one BNC connector for connecting I/O racks. The baseplate has a code lock, see Table 4 on page 75, that prevents installation of an incorrect type of unit onto the TP865 Baseplate. The CI865 expansion unit contains the CEX-Bus logic, ControlNet bus logic, CPU and a DC/DC converter that supplies appropriate voltages from the +24 V supply, via the CEX-Bus.Neither R(un) nor F(ault) LED’s are ON The CI865 unit is in the process of being configured. Allow time for this to finalize. If the condition persists, and no other unit LED on the CEX-Bus is lit: ? Check the CEX-Bus fuse inside the PM8xx processor unit ? Initiate a reset signal (INIT) from the PM8xx processor unit ? Replace the CI865 unit F(ault) LED is ON The CI865 unit is in the process of being restarted. Allow time for this to finalize. Replace unit if the condition persists. COM A/COM B LED is OFF Power OFF or Reset Mode COM A/COM B LED is solid green Channel OK COM A/COM B LED is flashing green Temporary error or need initial setup COM A/COM B LED is solid red Module is broken, has to be replaced COM A/COM B LED is flashing red Bad channel cable
2.產 品 展 示
3.公 司 優 勢 主 營 產 品
4.相 關 產 品 展 示
本篇文章出自瑞昌明盛自動化設備有限公司，轉載請附上此鏈接:
