350噸雙缸液壓打包機

 配用動力：37KW，

臺時產量：3-5個包塊，

包重：1500-3000KG，

油缸：Φ220*2支，

操作方便，

 接上電源后打包 , 于一切輕泡、松散物料的打包?？蓱?yīng)用于用于有色金屬板材及型材和輕簿型塑料，棉、羊毛、廢紙、廢紙箱、廢紙板、紗線、塑料、布匹、編織袋、針織絨、麻、麻袋、毛條、毛球、繭、蠶絲、啤酒花、麥柴、草、廢塑料袋等一切輕泡、松散物料。包型緊湊，整齊美觀，可大幅降低運輸成本，是棉產區、紡織企業、超市、服裝廠、廢舊物資回收業和其他各種輕工業企業*的生產工具 。公稱壓力有30,60,80，100,120,150,200,250,300,350噸。另可根據用戶要求設計和定制。

350噸雙缸液壓打包機  

型號：350，公稱壓力主缸KN：3500

液體zui大工作壓力MPa:25，料箱尺寸長2400mm,寬1100mm,高:1600mm

包塊尺寸:長2400mm*寬:1100 *高:(1000）mm

包塊密度kg/m3：≥2200

單次循環時間S：85

電機功率KW：37

油缸行程：1200-1350MM

機器外形尺寸mm：長3100*寬2200*高5000。

整機重量T；21.

使用說明：

本廠使用68#液壓油，連接電源三相380V，額定電流為40A，安裝時要有接地保護，電機要根據所示方向運轉才能啟用，否則不能啟動。油箱加入液壓油方可啟動使用。但當氣溫降低時液壓油濃度大，機內的濾清器不能起到過濾作用，這時必須將濾清器拆出，待溫度恢復后，方可生新安裝使用。（注：濾清器應每月清洗1-2次）。

       溢流筏-控制該機的壓力開關,旋轉調壓手轉向右轉為增壓，向左轉為減壓，出廠前已調整好壓力。但在使用過程中調壓手輪可能有變位現象，導致壓力升高或降低，這時需要生新調節壓力，調壓時應在運轉中進行，同時把壓板降至zui低位置，調整溢流筏的調壓手輪，調整壓力不能高于或低于壓力表所示的范圍，壓力的OMPA（100KG/1cm2）。旁桿-增強壓的剛性和起導向作用，每次使用前應加油，起潤滑作用。

      行程開關-控制該機的啟動和停止的作用，因此要經常檢查、維修、保養。手動轉向閥-控制壓板向上向下，停止的開關。

      1、手動轉向閥打向下檔位時壓板自動向下工作，當廢紙壓到結實狀態時，那阻力大于壓力：壓板不能再向下壓，應把手動轉向閥打向空檔位置，停止加壓，如果*處于加壓狀態，會導致液壓，電機、油泵長時間處于超負荷狀態而使各機件損壞。

     2、手動轉向閥打向升檔位置，壓板自動向上升到zui高的位置，由行程開關控制自停，這時應把手動轉向空檔位置。完成一個工作程序。

350 tons of heavy hydraulic balers

Metal copper packer (stainless steel baler),

 Equipped with power: 37KW,

Taiwan when the output: 3-5 mass,

Package weight: 1500-3000KG,

Cylinder: Φ220 * 2,

Easy to operate,

 Connected to the power after packaging, dedicated to all light foam, loose material packaging. It can be used in non-ferrous metal sheet and profile and light-type plastic, cotton, wool, waste paper, waste paper box, waste paperboard, yarn, plastic, cloth, woven bag, knitted cashmere, hemp, Hair ball, cocoon, silk, hops, wheat chai, grass, waste plastic bags and so on all loose foam, loose material. It is a necessary production tool for cotton producing areas, textile enterprises, supermarkets, garment factories, waste materials recycling industry and other light industrial enterprises. The nominal pressure is 30,60,80,100,120,150,200,250,300,350 tons. The other can be designed and customized according to user requirements.

350 ton double cylinder hydraulic baler

Model: 350

Nominal pressure master cylinder KN: 3500

Liquid maximum working pressure MPa: 25

Box size 2400mm long, 1100mm wide, high: 1600mm

Package size: length 2400mm * width: 1100 * high: (1000) mm

Bulk density kg / m3: ≥2200

Single cycle time S: 85

Motor power KW: 37

Cylinder travel: 1200-1350MM

Machine Dimensions mm: Length 3100 * Width 2200 * Height 5000.

Weight T; 21.

Instructions for use:

The factory is equipped with 68 # hydraulic oil, connected to the power supply three-phase 380V, rated current of 40A, the installation should be ground protection, the motor should be operated according to the direction shown to be activated, or can not start. Fuel tank can be used to start the use of hydraulic oil. But when the temperature drops when the hydraulic oil concentration, the machine can not play a filter filter, then the filter must be removed until the temperature is restored before the new installation and use. (Note: the filter should be cleaned 1-2 times per month).

       Overflow raft - control the machine's pressure switch, rotary pressure hand turn right to pressurized, turn left to decompression, the factory has been adjusted before the pressure. But in the course of the use of pressure handwheel may have a displacement phenomenon, resulting in increased or decreased pressure, then need to add a new regulation of pressure, pressure should be carried out in the operation, while the pressure plate to the lowest position, adjust the overflow Rafts of the pressure regulating handwheel, the adjustment pressure can not be higher or lower than the pressure gauge shown in the range of optimum pressure for OMPA (100KG / 1cm2). Side bar - to enhance the rigidity of the pressure and play a role, each should be used before the fuel, from the lubrication.

      Stroke switch - to control the machine's start and stop the role, so often check, repair, maintenance. Manual steering valve - control the pressure plate up and down, stop the switch.

      1, manual steering valve to play down when the pressure plate automatically down work, when the waste paper to a strong state, that resistance is greater than the pressure: the pressure plate can not be pressed down, the manual steering valve should be turned to neutral position, stop Pressurized, if the long-term pressure state, will lead to hydraulic, motor, pump for a long time in a state of overload and damage to the parts.

     2, manual steering valve to the upshift position, the platen automatically rose to the highest position, controlled by the trip switch from the stop, then the manual should be turned to the neutral position. Complete a working procedure.