騰達試驗儀器廠：

　　瀝青旋轉薄膜加熱試驗的規定制造，適用于測定道路石油瀝青薄膜加熱后的質量損失，并可測定加熱殘留物的針入度、粘度、軟化點及廷度等性質的變化，以評定瀝青的耐老化性能，并可代替普通烘箱使用。

　　Asphalt film rotary oven is a testing device for asphalt.It is suitable for measuring the performance change of semi-solid asphalt under the action of heating and air.Asphalt film rotary oven is based on the requirements of GB/T5304,T0610-1993,ASTMD2872 asphalt rotary film heating test Manufacture,suitable for measuring the mass loss of road petroleum asphalt film after heating,ａnd can measure the change in properties such as penetration,viscosity,softening point and tint of heating residue,etc.,to evaluate the aging resistance of asphalt,ａnd can replace ordinary asphalt Oven use.

　　瀝青薄膜旋轉烘箱技術參數：

　　★加熱功率：3.5kW

　　★工作室溫度：163℃

　　★控溫精度：±0.5℃

　　★轉盤轉速：15±0.2r/min

　　★噴氣流量：4±0.2l/min

　　★一次試樣數：8個

　　★不銹鋼內腔，

　　★電腦控制和測定溫度，數字顯示

　　★風量由流量計監測，老化85min后自動報警

　　★工作環境:

　?、匐娫矗?20V±10%50Hz AC

　?、诃h(huán)境溫度：5～50℃

　?、巯鄬穸龋骸?5%

　　★外形尺寸：750X700X1260mm

　　★重量：116kg

　　Asphalt film rotary oven technical parameters:

　　★Heating power:3.5kW

　　★Working room temperature:163℃

　　★Temperature control accuracy:±0.5℃

　　★Turntable speed:15±0.2r/min

　　★Airflow:4±0.2l/min

　　★Number of samples at one time:8

　　★Stainless steel inner cavity,

　　★Computer controlled and measured temperature,digital display

　　★The air volume is monitored by the flow meter,ａnd the alarm will be automatically issued after aging for 85min.

　　★Working environment:

　?、貾ower supply:220V±10%50Hz AC

　?、贏mbient temperature:5～50℃

　?、跼elative humidity:≤85%

　　★Dimensions:750X700X1260mm

　　★Weight:116kg

　　瀝青薄膜旋轉烘箱結構說明：

　　★總體安排：主體由薄鋼板構成，上半部是裝有雙重門的工作室，下半部是電器控制部分和機械減速傳動裝置，外表噴漆。

　　★觀察：工件室門是雙重形式，內層厚約30mm，外層厚約50mm，中裝有方形玻璃觀察窗。在室內有照明燈，可以在測定進行時能方便池從外面看到室內狀態，溫度計從上部前面插入。

　　★加熱：加熱裝置在工作室底部，采用空氣自然對流法加熱空氣。通過上下和背后的風道均勻加熱工作室。

　　★保溫和控溫：工作室和箱殼之間是保溫層和風道，為使工作室內溫度不致外導而影響恒溫和恒溫靈敏度，保溫層內充填玻璃纖維，風道和工作室壁上噴高銀粉漆。控溫分粗細兩種，通過長轉換開關在0、1／3、2/3、1、三段中的轉換，改變電熱絲加熱功串獲得粗略的升溫和控溫。調整安裝在工作室上部的電接點溫度計觸點，獲得的工作溫度。

　　★工作室：工作室中裝有可以放置四只瀝青盛樣皿的轉盤它由電機帶動。也可以取去轉盤，作為普通很恒溫箱使用。

　　Asphalt film rotary oven structure description:

　　★General arrangement:The main body is made of thin steel plate.The upper half is a working room equipped with double doors.The lower half is an electrical control part and a mechanical reduction transmission.The exterior is painted.

　　★Observation:The door of the work chamber is a double form.The inner layer is about 30mm thick and the outer layer is about 50mm thick.A square glass observation window is installed in it.There is a light in the room,so that the pool can easily see the indoor state from the outside while the measurement is in progress,ａnd the thermometer is inserted from the upper front.

　　★Heating:The heating device is located at the bottom of the studio,ａnd the air is heated by natural air convection.The studio is evenly heated by the up and down air ducts.

　　★Insulation and temperature control:The insulation layer and air duct are located between the studio and the casing.In order to prevent the temperature in the working room from affecting the constant temperature and the constant temperature sensitivity,the insulation layer is filled with glass fiber,ａnd the air duct and the studio wall are sprayed high Silver paint.The temperature control is divided into two types of thickness,through the long transfer switch in the 0,1/3,2/3,1,three sections to change the heating wire heating power string to obtain rough temperature rise and temperature control.Adjust the electrical contact thermometer contact installed in the upper part of the working room to obtain the specified operating temperature.

　　★Workshop:The workroom is equipped with a turntable where four asphalt containers can be placed.It is driven by a motor.You can also remove the turntable and use it as an ordinary thermostat.

　　瀝青薄膜旋轉烘箱使用方法：

　　★電源設備：應在供電線路中裝有超負荷的保險裝置，供此箱專用。并具有良好的接地裝置。

　　★校平烘箱：使轉盤在水平面上旋轉，旋轉時與水平面的傾角不得大于3度。

　　★溫度校正：

　　A、裝上溫度計(溫度計水銀球底部距離轉盤項面約6.4mm)校對電接點溫度計至所需溫度163℃。

　　B、關閉配電盤上所有開關，將電源插頭插上，打開電源開關。

　　C、將3段轉換開關指向1的位置，待整個工作室溫度上升至所需溫度時(163℃)應檢查工作溫度計讀數，通過調整電接點溫度計觸點來獲得工作室的正確溫度。粗略估計163℃恒溫功率1300瓦，這時應把3段轉換開關指向2/3處(1600w)待整個工作室在電接點溫度計控制下，恒溫15min，既可進行瀝青薄膜測定。

　　★將盛有試樣的盛樣皿放置轉盤上，關閉烘箱，使轉盤旋轉，恒定烘箱溫度在163℃。

　　★在箱子運轉中，室內照明燈不要隨意啟開，以免影響工作室溫度的穩定。

　　★完畢后，必須切斷各個開關。

　　Asphalt film rotary oven use method:

　　★Power supply equipment:overload safety devices should be installed in the power supply line for this box.And has a good grounding device.

　　★Leveling Oven:Rotate the turntable on a horizontal plane,ａnd the inclination angle with the horizontal plane during rotation should not be greater than 3 degrees.

　　★Temperature correction:

　　A.Install a thermometer(the bottom of the mercury ball of the thermometer is about 6.4mm from the surface of the turntable)to calibrate the electrical contact thermometer to the required temperature of 163°C.

　　B.Turn off all switches on the switchboard,plug in the power plug,ａnd turn on the power switch.

　　C.Point the 3-segment transfer switch to the position 1.When the temperature of the entire working room rises to the required temperature(163°C),check the working thermometer reading and obtain the correct temperature of the working room by adjusting the electrical contact thermometer contact.A rough estimate is 1300 watts at a constant temperature of 163°C.At this time,the 3-stage transfer switch should be pointed at 2/3(1600w).The whole studio can be controlled for 15 minutes under the control of an electric contact thermometer to measure asphalt film.

　　★Place the sample dish containing the sample on the turntable,close the oven,ａnd rotate the turntable.The constant oven temperature is 163°C.

　　★During the operation of the box,do not turn on the interior lighting at will,so as not to affect the stability of the studio temperature.

　　★When finished,you must turn off each switch.