A． 電控系統 

采用日道PLC電子控制系統及變頻器，一體化控制，功能完善，適應性強、功耗低。采用集成電路無觸點控制，可根據自身工藝要求隨意更改系統控制程序。

Fully Automatic Electric-control System

adopt Nippon PLC Electric-control system and inverter, It features in incorporate control, perfect funciton, stong adaptabillty, and low power consumption. It adopts non-contactcontrol by in tegrated circuirt, which can freely alter the systematic controlling program me according to the requirements of its techics.

B．飛達座

采用印刷機的飛達頭設計，加強型的送紙裝置，吸紙準確，送紙平滑順暢，配備連續疊紙系統，*高效運轉要求。

Feeder base

It adopts HMA printer with feeder head design, stengthen type feeding device, which ensures a accurate paper adsorbing and a smooth paper feeding. It is equipped with constant paper-piling system, which ca fully satisfy the requirement of high efficient operation.

C．底紙送紙部

采用吸風皮帶送紙及伺服馬達驅動，分別對應A/B/E浪三層，五層瓦楞底紙及卡、板底紙，輸送準確順暢。

Substrate Paper Feeding Section

Adopt air-absorbing belt to feed the paper driven by motor, which corresponds to A/B/Eflute three-layer, five-aayer corrugated paper and cardboard and substrate board paper and ensure an accurate andsmooth feeding.

D．微調調整器

日產原裝微動相位調整器，配合正時對位系統，可于機械高速工作時調整貼合誤差而無需停機。

Micro-tuning Regulator

Original Nippon micro-tuningphase regulator is combined sith timing para system; It can adjust the sticking error in the Non-stop state when the machine works in high speed. 

E．傳動系統

以進口時規皮帶替代傳統齒輪鏈條，*解決因金屬鏈條磨損而造成面底紙貼合不準之問題。

Transmission system

Replace the traditional gear chain with imported timing belt, which can perfectly solve the problems ofinaccurate sticking problem aroused from metal chain abrasion.

F．齊紙正時部

采用同步后推進式檔規，面底檔規同步推動面紙及底紙進入貼合部，并可不停機微調面底紙之貼合精度。

Paper Triming andTiming Section

Adopt the synchronous pushing mode rollers, substrate & litho rollerswill push synchro-nously the litho paper and substrate paper into the sticking section, and adjust the gluing precision between litho andsubstrate paper by micro tuning in the non-stop state.

G．膠水涂布系統

全自動膠水補充裝置，配合膠水流失回收循環，避免膠水浪費。依產品要求，可調整膠水厚度控制輪，配合特殊花紋膠輥，有效解決涂布甩糊問題并節省膠水消耗。

Glue coating system

Automatic glue-adding device is combined with a run-off glue recycling system, which can avoid waste of glue. According to the requirement, the controlling wheel can be adjusted for control of glue thikness and can be equipped with special embossing glue roller, which efficentlysove the problems of swing and pasting during coatingand save the consumption of  glue.

l          調換不同規格產品只需時約6-10分鐘，更適合短單產品；

l          可在高速工作時調整貼合誤差而無需停機；

l          面紙配置雙重上面紙結構，堆紙高度達1.8米，預疊式送紙更節約時間；

l          底紙吸風裝置采用中心向外擴張，更適應不同規格底紙，令送紙更加順暢；

l          給紙采用電磁制動系統，異常剎車停止時，無慣性轉動，不浪費紙張；

l          面紙及底紙采用同步光電控制技術，避免底紙或面紙不到位的問題；

l          所有電控，時規皮帶、電機均采用日本、美國、中國臺灣元口器件。

l          Size changeover needs only 6-10min, so more suitable for short and single product;

l          Adjustment of joint error is available when running at high speed without stop-press;

l          Double upper surface paper structure; stacking paper up to 1.8m; pre-folded feeding mode to save time more;

l          Bottom paper indraught device operates in the way from center to the outside to adapt to different sizes, so paper is fed smoothly more;

l          Feeding adopts electromagnetic braking system; when abnormal stoop, no inertial rotation exists to avoid paper waste;

l          Surface and bottom paper adopt synchronous photoelectric control technology to avoid unreachable bottom paper or surface paper;

l          All electrically-controlled bolts and motors adopt elements and components made in Japan, USA and Taiwan.