一、產品簡介：

紡織布料撕裂強度試驗機使用新控制技術，通過進口原裝交流數字控制器控制伺服電機配合同步帶使一副高精度滾珠絲杠移動試臺，試臺能以0.001mm/min—500mm/min速度運行。在測力源上使用美國銓力高精度拉壓傳感器，其精度達到0.02%，靈敏度高，整個系統可達到0.5級精度，有效測力范圍為大力值的0.2%到%；速度精度為示值的±0.5%以?xún)?nèi)；位移精度為示值的±0.5%以?xún)?nèi)；變形測量精度為示值的±0.5%以?xún)?nèi)。

1. Product introduction:

The textile fabric tear strength testing machine uses new control technology, and the imported original AC digital controller controls the servo motor and the synchronous belt to make a pair of high-precision ball screw move the test table. The test table can be at a speed of 0.001mm / min-500mm / min run. Using the imported high-precision tension and compression sensor imported from the United States Quantum Force, the accuracy reaches 0.02%, the sensitivity is high, the entire system can reach 0.5 grade accuracy, the effective force measurement range is 0.2% to% of the vigorous value; the speed accuracy is Within ± 0.5% of indicated value; displacement accuracy within ± 0.5% of indicated value; deformation measurement accuracy within ± 0.5% of indicated value.

二、技術參數：

★大拉力：5-50KN 大壓力：50KN

★高精度傳感器精度：±0.5%

★負荷精度：±1% 分辨率1/20000碼

★速度精度： ±0.5%

★速度范圍：1-250mm/min

★位移測量精度0.1mm

★大變形測量范圍：標線-1000mm（選配）

★移動橫梁有效行程：1000mm

★位移精度：示值相對誤差±0.5%

★電源：AC220V 50Hz

★外形尺寸960*780*2300mm（長*寬*高）

★凈重：750kG

2. Technical parameters:

★ High tension: 5-50KN Large pressure: 50KN

★ High precision sensor accuracy: ± 0.5%

★ Load accuracy: ± 1% resolution 1/2000 yards

★ Speed accuracy: ± 0.5%

★ Speed range: 1-250mm / min

★ Displacement measurement accuracy 0.1mm

★ Large deformation measurement range: marking line -1000mm (optional)

★ Effective travel of moving beam: 1000mm

★ Displacement accuracy: relative error of indication value ± 0.5%

★ Power supply: AC220V 50Hz

★ Overall dimensions 960 * 780 * 2300mm (length * width * height)

★ Net weight: 750kG

三、產品特點：

★自動清零：計算機接到試驗開始指令，測量系統便自動清零

★自動返車：自動識別試驗斷裂后，活動橫梁自動高速返回初始位置

★自動存盤：試驗數據和實驗條件自動存盤，杜因突然斷電忘記存盤引起的數據丟失

★測試過程：試驗過程及測量、顯示、分析等均由微機完成

★顯示方式：數據和曲線隨試驗過程動態顯示

★結果再現：試驗結果可任意存取，可對數據曲線再分析

★曲線遍歷：試驗完成后，可用鼠標找出試驗曲線逐點的力值和變形數據，對求取各種材料的試驗數據方便實用。

★結果對比：多個試驗特性曲線可用不同顏色疊加、再現、放大、呈現一組試樣的分析比較；

★曲線選擇：可根據需要選擇應力應變、力時間、強度時間等曲線進行顯示和打?。?/p>

★批量試驗：對參數相同的試驗一次設定后可順次完成一批試樣的試驗；

★試驗報告：（可根據客戶需要）

拉伸：大力、拉伸強度、斷裂伸長率、彈性模量等

彎曲：大力、彎曲強度、撓度、彈性模量等

壓縮：大力、壓縮強度、屈服強度、彈性模量等，也可按用戶要求的格式對試驗報告進行編程和打??；

★限位保護：具有程控和機械兩級保護；

★過載保護：當負載超過額定的10%時自動停機；

緊急停機：設有急停開關，用于緊急狀態切斷整機電源；

★自動診斷：系統具有自動診斷功能，定時對測量系統，驅動系統進行過壓，過流、超溫等到檢查，出現異常情況即刻停機。

3. Product features:

★ Automatic zero-clearing: the computer receives the test start instruction, and the measurement system is automatically zero-cleared

★ Automatic return: After automatically identifying the test break, the movable beam automatically returns to the initial position at high speed

★ Automatic saving: automatic saving of test data and experimental conditions to prevent data loss caused by sudden power failure and forgetting to save

★ Testing process: The testing process and measurement, display, analysis, etc. are all done by the microcomputer

★ Display mode: data and curves are dynamically displayed with the test process

★ Result reproduction: The test results can be accessed at will, and the data curve can be re-analyzed

★ Curve traversal: After the test is completed, you can use the mouse to find the point-by-point force value and deformation data of the test curve, which is convenient and practical for obtaining the test data of various materials.

★ Comparison of results: Multiple test characteristic curves can be superimposed, reproduced, enlarged, and presented for analysis and comparison of a set of samples in different colors;

★ Curve selection: You can select stress and strain, force time, strength time and other curves to display and print according to your needs;

★ Batch test: After the test with the same parameters is set once, the test of a batch of samples can be completed in sequence;

★ Test report: (according to customer needs)

Stretching: strong force, tensile strength, elongation at break, elastic modulus, etc.

Bending: strong, bending strength, deflection, elastic modulus, etc.

Compression: Vigorously, compressive strength, yield strength, elastic modulus, etc the test report can also be programmed and printed in the format required by the user;

★ Limit protection: with two levels of program control and mechanical protection;

★ Overload protection: when the load exceeds 10% of the rated value, it will automatically stop;

Emergency stop: There is an emergency stop switch, which is used to cut off the power of the whole machine in an emergency state;

★ Auto-diagnosis: The system has an auto-diagnosis function. It regularly checks the measurement system and the drive system for over-voltage, over-current, and over-temperature, etc and immediately stops when an abnormal situation occurs.