滾珠軸承式耐磨試驗機概述：適用于按國標GB/T16925-1997，混凝土及其制品耐磨性試驗方法，對混凝土及其制品、路面磚、地面磚、人造大理石、水磨石等建筑材料進行耐磨試驗

I. Overview of Ball Bearing Abrasion Tester: Applicable to the test method of abrasion resistance of concrete and its products according to GB / T16925-1997, for construction materials such as concrete and its products, pavement tiles, floor tiles, artificial marble, terrazzo, etc. Abrasion test

滾珠軸承式耐磨試驗機技術參數：

★磨頭：13*15.875mm滾珠軸承

★磨頭上的壓力負荷： 154±2.5N

★轉軸負荷額定轉速：1000-1050r/min

★磨石工作硬度：大于HRC62

★測量行程：10mm

★噪音 ：≯75dB

★適和試件規格受磨面積：≮100*100mm≯300*300mm

★電機功率 ：0.75kw

★外形尺寸（長*寬*高）：700*450*800mm

★凈重：163kg

Technical parameters of ball bearing abrasion tester

★ Grinding head: 13 * 15.875mm ball bearing

★ Pressure load on the grinding head: 154 ± 2.5N

★ Rotary shaft load rated speed: 1000-1050r / min

★ Working hardness of grinding stone: greater than HRC62

★ Measurement stroke: 10mm

★ Noise: ≯75dB

★ Suitable Specimen Specs Abraded Area: ≮100 * 100mm≯300 * 300mm

★ Motor power: 0.75kw

★ Dimensions (length * width * height): 700 * 450 * 800mm

★ Net weight: 163kg

滾珠軸承式耐磨試驗機安裝與使用：

★本機采用木箱包裝，開箱后應檢查產品合格證，集裝單，使用說明書等資料是否全，并根據產品裝箱查對箱內物件是否完備相符。

★打開箱檢驗合格的試驗機應水平放在工作臺上，本機不需要特別基礎和地腳螺栓，只要保證水平和穩定性****可以。

★插上進水管并與水源接通，插上出水管，本機的四芯插頭接控接上三相380V交流電源，并可靠接地，即可投入使用。

★將試件的受磨面朝上，放入試件夾具架內，試件夾具架內有移動板，可根據試件不同寬度變進行調整，通過水平調盤，將受磨面調整水平位置后，轉動壓緊螺桿夾緊試件。

★將磨頭放在受磨面上，轉動升降手柄使機架和中空轉軸下降并壓在磨頭上，磨頭的滾珠應全部對準中空轉軸下端滾道，謹防中空轉軸碰磨頭上傳感器

★繼續轉動升降手柄，使機架繼續下降至傳感器的頂部與紅刻線對齊，同時，百分表的測量桿應與頂板相接觸，并應有5mm的里程。

★轉緊鎖緊手柄板上防護罩開啟水源，待水中空轉軸內不斷流向試件的受磨面時，開始試驗。

★按下控制器的“欲動”按鈕，電機開始工作，當磨頭轉30轉左右時，自動停止，記下百分表的讀書，按下“復位”按鈕，使數碼顯示復零。然后再按下“起動”按鈕，本機即開始運轉，當磨頭轉至1000轉時，自動停止記下百分表的讀數，再一次按下“起動”按鈕，本機繼續運轉而后，每轉1000轉，磨頭**會自動停止，同時記下百分表讀數，但轉滿5000轉時，本機自動停轉并自鎖。要使本機重新運轉，必須按下“復位”按鈕，方可使本機正常運轉，本機運轉過程中，如要暫停試驗，可按下“停止”按鈕，即停轉數據自動保存，以便試驗數據的連續性。完整性和準確性。

★本機機架不能旋轉。

★試驗結束，關閉水源和電源，取出試件。

Third, the installation and use of ball bearing abrasion tester

★ This machine is packed in a wooden box. After opening the box, check whether the product certification, packing list, instruction manual and other information are complete, and check whether the contents of the box are complete and consistent according to the product packing.

★ The testing machine qualified for opening the box should be horizontally placed on the workbench. This machine does not need special foundation and anchor bolts, as long as it is level and stable.

★ Plug the water inlet pipe and connect it to the water source, plug in the water outlet pipe, the four-core plug of this machine is connected to the three-phase 380V AC power supply, and it is reliably grounded, then it can be put into use.

★ Put the wear side of the test piece upwards into the test piece holder. There is a moving plate in the test piece holder. It can be adjusted according to the different width of the test piece. The horizontal position of the wear surface can be adjusted by the horizontal adjusting plate. Then, turn the compression screw to clamp the test piece.

★ Place the grinding head on the surface to be worn, turn the lifting handle to lower the frame and the hollow shaft and press it on the grinding head. The balls of the grinding head should be aligned with the lower rollers of the hollow shaft. Be careful that the hollow shaft does not touch the sensor on the grinding head

★ Continue to rotate the lifting handle so that the frame continues to descend until the top of the sensor is aligned with the red engraved line. At the same time, the measuring rod of the dial indicator should be in contact with the top plate, and it should have a 5mm mileage.

★ Turn on the protective cover on the locking handle plate to turn on the water source, and wait for the flowing surface in the water to continue to flow to the abraded surface of the test piece, and start the test.

★ Press the controller's "Move" button, the motor starts to work, when the grinding head rotates about 30 revolutions, it will automatically stop, write down the dial indicator and press the "Reset" button to reset the digital display to zero. Then press the "Start" button again, the machine will start to run. When the grinding head is turned to 1000 revolutions, it will automatically stop recording the dial indicator reading. Press the "Start" button again, the machine will continue to run, and every time When the rotation is 1000, the grinding head ** will stop automatically, and the dial indicator reading will be recorded at the same time, but when the rotation is over 5000, the machine will automatically stop and lock itself. To make the machine run again, you must press the "Reset" button to make the machine run normally. During the running of the machine, if you want to pause the test, you can press the "Stop" button, the stall data is automatically saved, so that Continuity of test data. Completeness and accuracy.

★ The machine frame cannot be rotated.

★ After the test, turn off the water and power and remove the test piece.

滾珠軸承式耐磨試驗機結構：如圖：

Fourth, the structure of ball bearing abrasion tester: Figure:

主機由底座（1），立柱（13），機架（11），電機（15），中空轉軸（5），磨頭（滾珠軸承）（4），試件夾具（2）等組成。電機（15）與機架（11）連接，通過皮帶（12）帶動中空轉軸（5）工作時，中空轉軸在垂直方向無約束，中空轉軸（5）和配垂（10）輔件的自重全部壓在磨頭上。

The main unit consists of a base (1), a column (13), a frame (11), a motor (15), a hollow shaft (5), a grinding head (ball bearing) (4), and a test fixture (2). The motor (15) is connected to the frame (11). When the hollow shaft (5) is driven by the belt (12), the hollow shaft is unconstrained in the vertical direction. Press on the grinding head.

滾珠軸承式耐磨試驗機維護和保養：

1、試驗結束后，將試驗機，主柱及所有工作部分把誰擦干，然后加上防銹油。

2、本機傳動部分定期加潤滑油，不使用時應每月運轉一次。

3、使用過程中，應經常檢測磨頭滾珠直徑，小于15.675MM必須更換。

Fifth, the ball bearing type wear test machine maintenance and maintenance:

1. After the test, wipe the test machine, the main column and all working parts, and then add anti-rust oil.

2. The transmission part of this machine is regularly lubricated. When not in use, it should be run once a month.

3. During use, the diameter of the ball of the grinding head should be checked frequently. If it is less than 15.675MM, it must be replaced.

滾珠軸承式耐磨試驗機注意事項：

★該機采用三相380V電源，機外殼必須接地，設備未經可靠接地嚴禁使用。

★磨頭在運轉過程中，百分表必須固定，百分表測量頭和頂板脫離接觸，當運轉停止，測量頭與頂板接觸并讀數。

★在試驗中，百分表測得磨面面深度≯1.5mm，以防磨頭的軸承架磨損毀壞，不準繼續試驗。

★本機采用傳感器接收系統測量磨頭轉數，一旦發現磨頭在運轉而控制器的數碼顯示停止，應立即停機，檢查傳感器（6）的位置是否處于傳感器接收區域。

Six, matters needing attention of ball bearing type abrasion tester

★ This machine adopts three-phase 380V power supply. The casing of the machine must be grounded. The equipment must not be used without reliable grounding.

★ During the running process of the grinding head, the dial indicator must be fixed. The dial gauge measuring head and the top plate are out of contact. When the operation stops, the measuring head is in contact with the top plate and reads.

★ During the test, the depth of the ground surface was measured by a dial indicator mm1.5mm to prevent the bearing frame of the grinding head from being worn and damaged. It is not allowed to continue the test.

★ This machine uses a sensor receiving system to measure the number of rotations of the grinding head. Once it is found that the grinding head is running and the digital display of the controller stops, it should immediately stop and check whether the position of the sensor (6) is in the sensor receiving area.

滾珠軸承式耐磨試驗機裝箱單：

★耐磨試驗機1臺

★控制器1臺

★磨頭（滾珠軸承）1件

★百分表 1只

★升降手柄 1件

★鎖緊手柄1件

★配重塊1件

★說明書1本

★合格證1張。

Packing list of ball bearing abrasion tester

★ Abrasion tester

★ 1 controller

★ Grinding head (ball bearing) 1

★ Dial indicator 1

★ 1 lifting handle

★ 1 locking handle

★ 1 counterweight

★ 1 manual

★ 1 certificate of conformity.