一、砂基透水磚耐磨試驗機采用了擺線針輪減速機，減速比大，結構緊湊，傳動平穩，磨料流量可調，能有效地節約磨料的用量。該試驗機通過齒輪傳動減速達到鋼輪轉速75r/min，齒輪傳動相比皮帶傳動減速精準、平穩、不會出現打滑現象，鋼輪轉動由時間繼電器控制，電機轉到預定時間也**是轉到試驗要求的轉速，電機自動停止。鋼輪式耐磨試驗機，陶瓷磚耐磨試驗機本機適用于無釉磚、馬賽克、水泥路面磚等脆性材料的耐磨試驗，是為完善建筑陶瓷及配件生產企業的檢驗條件，提高檢測水平。
First,the sand-based permeable brick wear tester uses a cycloid pinwheel reducer,which has a large reduction ratio,a compact structure,a stable transmission,ａnd adjustable abrasive flow,which can effectively save the amount of abrasive.The testing machine can reduce the speed of the steel wheel to 75r/min through gear transmission.Compared with the belt drive,the gear transmission is accurate and stable,ａnd there is no slippage.At the speed required by the test,the motor stops automatically.Steel wheel abrasion tester,ceramic tile abrasion tester This machine is suitable for abrasion test of brittle materials such as unglazed tiles,mosaics,ａnd cement pavement tiles.Level,one of the inspection equipment necessary to ensure product quality.
二、砂基透水磚耐磨試驗機具有設計合理、結構簡單、造型美觀、操作方便、轉動平穩，達到試驗要求自動停機等特點，主要適用用于水泥磚的耐磨試驗。
Second,the sand-based permeable brick abrasion tester has the characteristics of reasonable design,simple structure,beautiful appearance,convenient operation,smooth rotation,automatic shutdown when it meets the test requirements,ａnd is mainly used for abrasion test of cement bricks.
三、砂基透水磚耐磨試驗機符合標準：
GB/T3810.7—2016《無釉磚耐磨試驗方法》
ISO/DIS10545/6—94《無釉磚耐深度磨損試驗方法》
GB/T12988-1009《無機地面材料耐磨試驗方法》
Third,the sand-based permeable brick abrasion tester meets the standards:
GB/T3810.7—2016"Abrasion Test Method for Unglazed Bricks"
ISO/DIS10545/6-94"Test Method for Deep Wear Resistance of Unglazed Bricks"
GB/T12988-1009"Test method for abrasion resistance of inorganic floor materials"
四、砂基透水磚耐磨試驗機技術參數：
●磨輪一：直徑200±0.2mm，厚度10±0.1mm，
●磨輪二：直徑200±0.2mm，厚度70±0.1mm，硬度HB203-245
●磨輪轉速：75±4r/min恒定；
●試樣尺寸：100mm×110 mm；
●磨料：粒度為ISO8486-1986中規定的F80白色熔融氧化鋁；
●磨料給入速度：（100±10）g/100r流量可調；
●貯料斗容積：大于5L；
●試驗時間：可預置，數字顯示；
●砝碼一：一質量為2.5㎏（適用GB/T3810.7-2006）；
●砝碼二：一質量為14㎏（適用GB/T12988-91）。
Fourth,the technical parameters of sand-based permeable brick wear tester
●Grinding wheel one:diameter 200±0.2mm,thickness 10±0.1mm,
●Grinding wheel two:diameter 200±0.2mm,thickness 70±0.1mm,hardness HB203-245
●Wheel speed:75±4r/min constant;
●Sample size:100mm×110 mm;
●Abrasive:particle size is F80 white fused alumina specified in ISO8486-1986;
●Abrasion feeding speed:(100±10)g/100r flow rate adjustable;
●Storage hopper volume:greater than 5L;
●Test time:presettable and digital display;
●Weight one:one weight is 2.5㎏(applicable to GB/T3810.7-2006);
●Weight two:one weight is 14㎏(applicable to GB/T12988-91).
五、砂基透水磚耐磨試驗機注意事項及其保養：
●接通電源線時，應注意電機正反轉，鋼輪應該按照箭頭指示方向旋轉；
●試驗機必須在接**志處可靠接地（線徑不小于1.5mm）；
●每次試驗后，應將試驗機打掃干凈，尤其應將夾具及其導軌上的沙子清理干凈；
●每一年應將齒輪箱側蓋板卸下，在齒輪上加適量鋰基潤滑脂。
●環境溫度：室溫
●周圍無腐蝕性性質
●地面堅固水平
●電源為380V，電壓波動范圍不超過額定電壓的10%
