PLC 工控機 嵌入式系統 人機界面 工業以太網 現場總線 變頻器 機器視覺 DCS PAC/PLMC SCADA 工業軟件 ICS信息安全 應用方案 無線通訊
上海榮計達儀器科技有限公司
上海榮計達儀器科技有限公司
暫無信息 |
鉛筆硬度計是檢測儀器，涂膜硬度是涂料制造、涂料使用（涂表）行業進行質量認定的必測指標
鉛筆硬度計是檢測儀器，涂膜硬度是涂料制造、涂料使用（涂表）行業進行質量認定的必測指標。鉛筆劃痕法測試涂膜硬度是八十年代以來被國際普遍采用的測試方法。我國也已在涂料的發展研究和工業生產中推廣這種測試方法。本儀器是根據 標準“涂膜硬度鉛筆測定法"《GB6379----86》第2 3 條手工操作法而設計制造的。儀器即可在實驗室使用，也可用也施工現場，并能在任意方向上對涂膜硬度進行檢定。
The pencil hardness tester is a testing instrument, and the hardness of the coating film is an indispensable indicator for quality certification in the coatings manufacturing and coatings (painting) industries. The pencil scratch method for testing coating film hardness is a test method generally adopted internationally since the 1980s. China has also promoted this test method in the research and industrial production of coatings. This instrument is designed and manufactured according to the manual method of Article 23 of the standard "Paint Film Hardness Pencil Method" "GB6379 ---- 86". The instrument can be used in the laboratory or at the construction site, and the hardness of the coating film can be verified in any direction.
鉛筆硬度計結構及工作原理：
儀器為機械式，三點接觸被測表面(二點為輪，一點為鉛芯)始終保證鉛筆與被測表面形成45° 夾角，用于推動儀器運動，即可完成測試過程。
Pencil hardness tester structure and working principle:
The instrument is mechanical, and three points contact the tested surface (two points are the wheel and one point is the lead core). Always ensure that the pencil forms a 45 ° angle with the measured surface.
鉛筆硬度計技術參數：
★筆尖重負：750±5g。
★鉛筆規格：6B～HB～6H（13支）。
★重 量：1.9Kg。
★外形尺寸：120×75×60mm（長×寬×高）。
★筆尖重負：500±5g。
★鉛筆規格：6B～HB～6H（13支）。
★重 量：1.6Kg。
★外形尺寸：90×75×60mm（長×寬×高）。
★筆尖重負：1000±5g。
★鉛筆規格：6B～HB～6H（13支）。
★重 量：2.4Kg。
★外形尺寸：130×75×60mm（長×寬×高）。
Technical parameters of pencil hardness tester:
★ Pen tip load: 750 ± 5g.
★ Pencil specifications: 6B ～ HB ～ 6H (13 pieces).
★ Weight: 1.9Kg.
★ Dimensions: 120 × 75 × 60mm (length × width × height).
★ Pen tip load: 500 ± 5g.
★ Pencil specifications: 6B ～ HB ～ 6H (13 pieces).
★ Weight: 1.6Kg.
★ Dimensions: 90 × 75 × 60mm (length × width × height).
★ Pen tip load: 1000 ± 5g.
★ Pencil specifications: 6B ～ HB ～ 6H (13 pieces).
★ Weight: 2.4Kg.
★ Dimensions: 130 × 75 × 60mm (length × width × height).
鉛筆硬度計重量
★筆尖荷重500g的硬度計，沒包裝前重量為2kg。加上泡沫紙皮等外包裝應該是2.5kg重量。
★筆尖荷重750g的硬度計，沒包裝前重量為2.4kg。加上泡沫紙皮等外包裝應該是3kg重量。
★筆尖荷重1000g的硬度計，沒包裝前重量為2.5kg。加上泡沫紙皮等外包裝應該是3kg重量。
Pencil hardness tester weight
★ The hardness of the pen tip load is 500g, the weight before packing is 2kg. Plus foam paper skin and other packaging should be 2.5kg weight.
★ The hardness of the pen tip is 750g, and the weight is 2.4kg before packaging. Plus foam paper skin and other packaging should be 3kg weight.
★ The hardness tester with a tip load of 1000g is 2.5kg before packing. Plus foam paper skin and other packaging should be 3kg weight.
鉛筆硬度計操作規程：
A準備
★按GB1727要求準備120*50*（0.2-0.3）平滑馬口鐵板或按產品規定的底材，制備涂膜。
★用鉛筆刀把每支鉛筆前端削去木質部分，露出5-6mm柱狀筆芯（注意鉛筆芯不可松動或削傷鉛芯），用手握住鉛筆，使鉛筆始終與400號砂紙成90°角，在砂紙上摩擦鉛芯端面，直到獲得一端平滑邊緣銳利的筆端為止（邊緣要無破碎或缺口）
★把削好的鉛筆插入鉛筆架上。調整鉛筆，使鉛筆芯工作端面與砝碼心重合（相應鉛芯工作端面與鉛筆架約25mm），然后用螺釘擰緊，使鉛筆位置固定。
★松開夾緊螺母，放入需測定的涂膜試片，然后擰緊螺母，使試片固定。
★松開止動螺釘，調整平衡錘，使工作桿平衡（即使鉛筆剛好接觸到試片上），然后擰緊止動螺釘，使鉛筆芯工作面離開涂膜試片。
★把砝碼輕輕放在鉛筆架上。
B 測試
★松開止動螺釘，使鉛筆芯輕輕降下到被測涂膜試片上。
★轉動手輪，使涂膜板朝劃痕方向移動大約5mm(順時針轉動手輪)，并留意觀察表面是否劃破。
★取下砝碼，更換鉛筆，旋動試臺旋扭，使試驗臺縱向移動一定距離更換試片劃痕位置，重復準備操作后，再做下一次試驗，依次用每種型號硬度的鉛筆一次犁出五道痕跡。
★從a硬的鉛筆開始用此方法，當鑒定五道痕跡中，若有兩次或兩次以上犁傷膜時，換上一級的鉛筆，直到找出五道痕跡中，只有一次犁傷涂膜的鉛筆（或沒有破壞）。則這一級鉛筆的硬度值 代表被測涂膜的硬度。
Pencil hardness tester operating procedures:
A ready
★ Prepare 120 * 50 * (0.2-0.3) smooth tinplate according to the requirements of GB1727 or the substrate specified by the product to prepare the coating film.
★ Use a pencil sharpener to shave the wooden part of the front end of each pencil to expose a 5-6mm columnar refill (note that the lead cannot be loosened or damage the lead). Hold the pencil with your hａnd so that the pencil is always at a 90 ° angle with 400-size sandpaper , Rub the end surface of the lead on the sandpaper until you get a smooth pen with a sharp edge at one end (the edge should be free of cracks or nicks)
★ Insert the sharpened pencil into the pencil holder. Adjust the pencil so that the working surface of the pencil lead coincides with the weight center (the corresponding working surface of the lead lead is about 25mm from the pencil holder), and then tighten with a screw to fix the pencil position.
★ Loosen the clamping nut, put the coating film test piece to be measured, and then tighten the nut to fix the test piece.
★ Loosen the stop screw, adjust the balance weight to balance the work rod (even if the pencil just touches the test piece), and then tighten the stop screw so that the working surface of the pencil lead leaves the test film.
★ Put the weight lightly on the pencil holder.
B test
★ Loosen the stop screw, and lower the pencil lead onto the test film of the test film.
★ Turn the handwheel to move the coating film about 5mm in the direction of the scratch (turn the handwheel clockwise), and pay attention to observe whether the surface is scratched.
★ Remove the weight, replace the pencil, rotate the test bench to make the test bench move a certain distance in the longitudinal direction to change the scratch position of the test piece, repeat the preparation operation, and then perform the next test, using each type of pencil in order Five traces were plowed.
★ Use this method from a hard pencil. When identifying five traces of plow injury film, if there are two or more plow injury membranes, change the pencil to the next level until you find one of the five traces. Paint the pencil (or not break). Then the hardness value of this grade pencil represents the hardness of the tested coating film.
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
智能制造網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
