| DM2436AB 是一只以 16 位元微處理器為計算核心，全數位化量測、顯示、校正、輸出的多功能電力表。因其微處理器之快速工作脈波 (16MHz) 及快速取樣，能夠提供高準確度的量測。 DM2436AB 除了能以單一表量測所有電力單位 (V、A、W、VAR、PF、WH、VARH、Hz) 外，還具有*大值、*小值量測，及設定值接點輸出等功能。在通信介面上，有串列的 RS-232 或 RS-485 可供選擇，以世界上極通用的 MODBUS RTU 為通信協定，提供使用者更方便的搭配。
|
| 特性 |
?Precision True-RMS measurement even for distorted waves
?High immunity to external noise
?RS485 standard communication interface output
?PT and CT scaling
?Memory for all setup and energy data
?Relay output (ΣV or ΣA or ΣW)
?Auto calibration from computer
?Maximum and Minimum function
?Power supply is AC 90V ~ 260V, 50/60Hz
?110×110mm case
|
| 詳細規格 |
| Display:4 digits (9999), 0.4" LED high (V, A, W, VAR, PF, Hz) | | 5 digits (99999), 0.4" LED high (WH, VarH) | | Accuracy:(at 23±5℃ sine wave) | | Voltage | ±0.1% of reading ±0.15% of range | | Current | ±0.1% of reading ±0.15% of range | | Watt | ±0.2% of reading ±0.3% of range | | Var | ±0.2% of reading ±0.3% of range | | Power factor | ±0.5% of reading | | PF polarity | "＋" lagging, "－" leading | | Watt hour | ±0.25% of reading ±1 Count | | Var hour: | ±0.4% of reading ±1 Count | | Hz | ±0.2% of reading | | Max. input over capability | Amp. 10A continuous | | | 50A for 5 sec | | | Volt. 750V continuous | | Conversion rate:(about) | 1/sec. | | Input burden | Volt. input ≦ 0.2 VA/phase | | | Amp. input ≦ 0.2 VA/phase | | Over input indication | "OL" | | Line voltage range | 35V～600V | | Phase voltage range | 20V～346V | | Current range | 50mA～5A | | Power factor range | ±0.5～±1 | | Frequency range | 45～65Hz | | CT, PT scaling factors | 1～9999 | | Setting for REF | 0.800～1.200 | | Operating temp. | 0～60℃ | | Storage temp. | -10～70℃ | | Temp. coefficient | ≦100PPM/℃ (≦60PPM/℃, 25℃ ±10℃) | | Max. relative humidity | 95% | | Dielectric strength | AC 2KV/1min. (input/output/power) | AC 2.8KV/1min. (input/output/power/case) | | Surge test | 4 KV/1.2 X 50μS, IEC 255-4 | | Dimensions | 110 (W)×110 (H)×135 (D) mm | | Mounting | Panel mounting | | Protocol | MODBUS, RTU | | Baud rate | 9600 | | Address range | 1～FF (Hex) | | Watt-hour data back-up time | 1000 Hours | | Aux. power | AC90～260V, 50/60Hz | | | DC24V, 48V, 110V±20% (option) | | Power consumption | AC6VA, DC5W | | Weight(about) | 700g |
|
TOP |
| 量測及顯示 |
| | Indicating | L1 (R) | L 2 (S) | L 3 (T) | Line
Voltage | Total | Items | VTRMS | V1 (L1～N) | V2 (L2～N) | V3 (L3～N) | V12,V23,V13 | V(Σ) | ATRMS | A1 | A2 | A3 | | A(Σ) | W | W(CH1) | W(CH2) | W(CH3) | | W(Σ) | VAR | VAR(CH1) | VAR(CH2) | VAR(CH3) | | VAR(Σ) | PF | PF(CH1) | PF(CH2) | PF(CH3) | | PF(Σ) | WH | WH(CH1) | WH(CH2) | WH(CH3) | | WH(Σ) | VARH | VARH(CH1) | VARH(CH2) | VARH(CH3) | | VARH(Σ) | Hz | Hz(CH1) | Hz(CH2) | Hz(CH3) | | Hz(Σ) |
V1, V2, V3：Phase voltage
V12, V23, V13：Line voltage |
TOP |
| 開孔尺寸 | PANEL CUT-OUT |
| |
TOP |
| 通信連結 |
RS-232C CONNECTION
The figure bellow illustrates the wiring requirements for connecting the DM2436AB using RS-232C communications. This can include a local direct connection to a
computer or other device. The RS-232C standard allows only a single point-to-point communications connection. Using this method, only one RS-232C equipped device may be connected to the serial port of the computer, or other device.The cable used between the computer is a standard RS-232Ccommunications cable with a maximum length of 50 feet (15.2m). | |
RS-485 CONNECTION
RS-485 communications allows multiple devices to be connected on the same bus. Up to 30 devices can be connected on a single RS-485 bus, which consists of a shield twisted pair cable. The overall length of the RS-485 cable connecting all devices cannot exceed 4000 ft (1219m). |
|
TOP |
| 輸出的腳位圖 |
|
RS-232/RS-485 WIRING DIAGRAM
|
TOP |
| 輸入的接線圖 |
A. 3 Phase 3 wires with 2CTs. 2PTs
| B. 3 Phase 3 wires with 3CTs. 2PTs
|
C. 3 Phase 4 wires 3CTs. 3PTs
|
D. 1 Phase 2 wires 1CTs. no PT
|
TOP |
| 訂購編號 | 輸出對照表 |
| DM2436AB was can also act as a comparison in addition to its measuring function. According to the real input value of A(Σ)、V(Σ) or W(Σ)，(not multiplied by CT or PT Ratio)，there are two points to be setted.
Illustrate as follow :
T1: H1 Relay ON
T2: H2 Relay ON |
會員1.png)
