G7104A Specification | |
| |
Standard | |
Frequency Accuracy | ± 0.05ppmInternal |
Frequency Aging | ± 0.5ppm/yr |
Display | 10.4"TFT LCD |
| 800 x 600 mode |
Frequency and Time Reference | |
Even Second | TTL |
10 ms | TTL |
10 MHz | -10 ~ +10 dBm |
Spectrum Analyzer | |
Input Frequency Range | 100kHz ~ 3GHz |
Maximum Input level | +30 dBm(1W) |
Amplitude Accuracy | ± 1dB |
Resolution Bandwidth | 100Hz, 300Hz, 1kHz, 3kHz, 10kHz, 30kHz, 100kHz, 300kHz, 1MHz |
Dynamic Range | ,+30 ~ -120dBm |
Input Attenuation | 0 ~ 50dB (Step: 5dB) |
SSB Phase Noise | ≤-90dBc/Hz |
Display Average Noise Level | < -125dBm @100Hz RBW |
Port 1 VSWR | <1.5 |
CdmaOne/Cdma2000 Tx Analyzer | |
Input Dynamic range | > -40 dBm |
Waveform Quality (ρ) | ± 0.005 for 0.9 < ρ < 1 |
Pilot Time Alignment Error | ± 1usec |
Frequency Error | ± 10Hz + Source Freq x Time Base Accuracy |
Code domain power | ± 0.5 dB (Rel.) |
Channel Power | ± 1 dB |
Adjacent channel power | ± 0.75 dB |
WCDMA Tx Analyzer | |
Input Dynamic range | > -40 dBm |
Pilot Time Alignment Error | ± 1usec |
EVM | ± 2.5% (Range: 15~20%) |
Frequency Error | ± 10Hz + Source Freq x Time Base Accuracy |
PCDE | ± 1.0% |
Code domain power | ± 0.5 dB (Rel.) |
Channel Power | ± 0.7 dB |
Adjacent channel power | ± 0.75 dB |
| |
Over The Air PN Scanner & Analysis (except in EV-DO and W-CDMA) | |
| |
PN Scanner (max 5 PN analysis) | Ec/Io, Delay Multipath Profile |
Analysis | |
Channel Power, Pilot Power, Noise Floor, Delta Paging Power, Delta Sync Power, PN Offset, Estimated Rho | |
Signal Generator | |
CW Signal | |
Frequency Range | 800 ~ 2,700MHz |
CW Output Level | -10 ~ -90dBm |
Level Accuracy | ± 1 dB |
cdmaOne/cdma2000/W-CDMA Signal | |
Frequency Range | 800 ~ 2,700 MHz |
Output Level | -30 ~ -80dBm |
Level Accuracy | ± 1.5dB |
Filter Type | IS-95B, 3GPP standard |
No of Carrier | 1 |
Assigned Walsh Code | CDMA: W64.0 |
| WCDMA: W256,0 |
Antenna/Cable | |
Maximum Input Power | |
without damage | 0.1W |
Cable Loss | |
Dynamic Range | 0 ~ 33dB |
Accuracy | ± 0.5dB |
Resolution | 0.01dB |
VSWR | |
Frequency Range | 800 ~ 2,700MHz |
Directivity | > 1.07 |
VSWR Range | 1.07 ~ 15 |
DTF | |
Range (m) | 0.1 ~ 300m |
Accuracy | 10m>: ±0.3m, |
| 10m<: ± 3% |
Resolution | 0.5% of Measurement Distance |
Power Meter | |
Maximum Input Power | |
without damage | 0.1W |
RF Power | |
Frequency Range | 0.1kHz ~ 3GHz |
Dynamic Range | ,+30 ~ -60dBm |
Accuracy | ±0.7dB |
Optical Power | |
Wavelength | 1310nm, 1510nm, 1550nm |
Accuracy | ±1dB |
Measurement Range | ,+15 ~ -30dBm |
Display Units | dBm, uW |
T1 Analyzer | |
Error Detect Code (BPV), FAS, CRC-4 | |
Alarm Detect | Red Alarm, Yellow Alarm, AIS Alarm |
Receive Level | +6 ~ -36dB DSX |
Electrical Interface | |
Connectors, Rx, Tx | Bantam(120ohm) |
Output | 0 dB, -7.5dB, and -15dB |
Line Code | AMI, B8ZS |
Impedance | 100 or 1000 ohm |
Input | |
Term/Bridge/Monitor/Loop | 0 ~ -20dB |
Transmitter and Receiver | |
Framing , ; | Superframe, ESF, SLC-96, T1DM |
Channel Formats | Full T1 |
Test Pattern | 1-8, 1-16, ALL1, ALL0, 0101, 3E-24, QRSS, 2E-23, |
| 2E-15, 2E-23 inverse, 2E-15 inverse |
Additional Functions | |
Reference Clock | Received or Internal |
Event Log Capability | internal memory or External USB memory |
Error Insertion | 1E-5, 1E-6, 1E-7 |
Error Rate Count | CRC, Frame, Code, Calculated BER |
Pulse Mask Checking | |
E1 Analyzer | |
Error Detect Code (BPV), FAS, CRC-4 | |
Alarm Detect | FAS RAI, MFAS RAI, AIS |
Receive Level | +6 ~ -36dB DSX |
Electrical Interface | |
Connectors, Rx, Tx | Bantam(120ohm) |
Output | 0 dB, -6dB Conforms to ITU-T Rec.G.703 |
Line Code | AMI, HDB3 |
Impedance | Term, Monitor : 120ohm, Bridge > 1,000ohm |
Input | |
Term/Bridge/Monitor | 0 ~ -20dB |
Transmitter and Receiver | |
Framing | Unframed, PCM-30, PCM-30 with CRC, PCM-31, PCM-31 with CRC |
Channel Formats | Full E1 |
Test Pattern | 1-8, 1-16, ALL1, ALL0, 0101, 20ITU |
Additional Functions | |
Reference Clock | Received or Internal |
Event Log Capability | internal memory or External USB memory |
Error Insertion | 1E-5, 1E-6, 1E-7 |
Error Rate Count | CRC, Frame, Code, Calculated BER |
Pulse Mask Checking | |
External Reference Clock | |
10MHz External Reference | |
Input Power | -10 ~ +10dBm |
Connector Type | BNC |
Even Second & 10ms Reference | |
Connector Type | SMA |
Input Level | TTL compatible |
Miscellaneous | |
Interface Ports Standard | |
RS-232(DB-9) | 1 port |
USB 1.1 | 1 port |
10Mbps LAN | 1 port |
Built-in Speaker | |
Dimension | |
Weight | 10.2Kg(Include Battery) |
Size (cm) | 31 X 36 X 15 |
Environment Conditions | |
Operating Temperature | .-5 ℃ ~ +50℃ |
Storage Temperature | .-20℃ ~ +70℃ |
Calibration Cycle | 1 year |
