詳細介紹
YCS主要技術參數
執行標準:GB/T1226-2001
精度: 1.5級
測量范圍:0.16、0.25??6MPa、10MPa
環境溫度:-20~+60℃
介質溫度:小于 60℃
安裝形式:徑向直接安裝(前帶邊及后帶邊可選)
過程連接:M20 × 1.5螺紋(其他螺紋可選)
防護等級:IP45
接頭材質:銅合金
波登管材質:銅合金
焊接:錫焊
表殼材質:黑鋼殼(噴塑)
密封圈、防爆塞材質:耐油橡膠
表玻璃:3mm平板玻璃 (有機玻璃、雙層安全玻璃可選)
機芯:銅合金
指針:鋁,黑色和紅色
表盤:鋁,白地黑字(特殊要求表盤可選)
YCS (YC) FOUNCTIONAL FEATURES
Executive standard: GB/T1226-2001
Accuracy: 1.5%
Ranges: 0.16、0.25??6MPa
Ambient temperature: -20~+60℃
Media temperature: less than 60℃
Mounting: bottom directly mounting (with front or back flange available )
Process connection: M20 × 1.5 (Other screw as request)
Protection class: IP45
Connection material: Copper alloy
Bourdon tube: Copper alloy
Welding: Tin-welding
Case material: Black steel (enameled)
Sealing circle and blow out vent material: Rubber
Window: 3mm plain glass (Organic or double layers available)
Movement: Copper alloy
Pointer: Aluminium, black and red color
Dial: Aluminium, white with black letters (Special dial available)
YCSH主要技術參數
接頭材質:316
波登管材質: 316
焊接:氬弧焊
機芯:不銹鋼
介質溫度:< 70℃
表殼材質:304不銹鋼
其他同 711
YCSH (YCF) FOUNCTIONAL FEATURES
Connection material: 316
Bourdon tube: 316
Welding: AISI 316 TIG Argonarc
Movement: Stainless Steel
Media temperature: 100℃
Others as 711
量 程 RANGES
產品使用說明 OPERATING INSTRUCTION
◆ 盤面的zui大刻度值即為zui大耐壓
◆ 建議使用的△ P(差壓值=P+ — P-)為盤面的1/2~1/3 為*。再小了就不好讀點。
△ P 一般不能小于1/10 的全量程。
◆ 紅針指示為正壓壓力(輸入壓力為P+);盤針指示為負壓壓力(輸出壓力P-)。盤針上的刻度可以和紅針形成夾角α直接讀數(從盤針上直接看刻度),也可以單獨用盤針在表盤上的示值與紅針在表盤上的示值進行計算得出差壓值△ P =P+ — P-
◆ 介質為氣體或液體,建議用在室內,使用溫度為-20℃~60℃
◆ 一般zui小量程做到0.16MPa,如需0.1MPa,可做到2.5 級
◆ 安裝時帶 ⊕號接頭接輸入壓力P+;帶⊙號接輸出壓力P-
◆ The highest indicated value is the highest pressure permitted.
◆ We advice using the 1/2~1/3 of the range as △P. it is convenient to see if it is too small.
△P is not low than1/10 of full scale value.
◆ The red pointer shows the plus pressure (the pressure input); the dial pointer shows the minus pressure(the pressure output).
◆ The value could be saw by the angle α between the red and dial pointers (see directly on the dial pointer).And we can compute the difference using the pointed values of the red pointer and the dial pointer(△ P =P+ — P-).
◆ It is suitable to measure gas and liquid medium, suggested in room in -20℃~60℃.
◆ The general lowest range is 0.16MPa. it is could be made to 2.5% if 0.11MPa requested.
◆ While mounting, the⊕ end should be deployed with pressure input terminal and the⊙ end should be deployed