上海朔川電氣設備有限公司

免費會員·9年

您現在的位置：上海朔川電氣設備有限公司>>西門子S7-1500>> 西門子6ES75221BL100AA0

西門子6ES75221BL100AA0

參考價:	面議

參考價:

面議

具體成交價以合同協議為準

產品型號
品牌
經銷商 廠商性質
上海市 所在地

訪問次數：226更新時間：2017-10-18 13:29:07

在線詢價加入對比查看聯系方式

聯系我們時請說明是智能制造網上看到的信息，謝謝!

分享

西門子S7-1500

上海朔川電氣設備有限公司

免費會員·9年

聯系人：: 吉夢琪

在線咨詢給我留言

掃一掃訪問手機商鋪

產品簡介

西門子6ES75221BL100AA0

產品介紹

西門子6ES75221BL100AA0 西門子6ES75221BL100AA0

6ES7522-1BL10-0AA0

SIMATIC S7-1500, 數字量輸出模塊, DQ32xDC 24V/0,5A, 32 通道 8 個一組, 4A 每組 inkl. 前連接器直插式

公司名稱：上海朔川電氣設備有限公司
聯 系人：吉夢琪
：
地址：上海市金山區涇波路129號
：2840735331

SM 522 數字量輸出模塊

訂貨數據
附件
產品信息
組態工具

跳轉到

概述

應用

設計

功能

技術規范

概述

8、16 和 32 通道數字量輸出模塊
靈活地選擇控制器以滿足相應任務需要
用于使用附加輸出對系統進行后續擴展
35 mm 寬的模塊具有參數設置和診斷功能
25 mm 寬的模塊可在狹小空間內使用：極為經濟，無參數設置或診斷功能

應用

數字量輸出模塊可以切換設備中的 24 V DC 或 230 V AC 電壓，從而可將內部信號從控制器傳輸至設備?？梢赃B接電磁閥、直流接觸器和指示燈。

35 mm 寬的輸出模塊具有可設定的參數和診斷功能，因此可根據相應過程要求進行靈活調整。

25 mm 寬的輸出模塊沒有可設定的參數或診斷功能，因此可極為方便地集成到工程系統中。建議將它們在只需要很少輸入通道的位置使用，或在必須在十分有限的空間內部署大量通道的情況下使用。

根據需要，可在一個站中并排使用兩種模塊。由于具有統一特性并采用共同的系統附件，處理十分方便。

提供了以下寬度為 35 mm 的數字量輸出模塊：

DQ 16x24VDC/0.5A ST；
數字量輸出模塊，16 通道 24 VDC / 0.5 A（晶體管）；兩個電壓組；每組 4 A；可設置診斷功能；可設置輸出替代值
DQ 32x24VDC/0.5A ST；
數字量輸出模塊，32 通道 24 VDC / 0.5 A（晶體管）；四個電壓組；每組 4 A；可設置診斷功能；可設置輸出替代值
DQ 8x24VDC/2A HF;
數字量輸出模塊，8 通道 24 VDC / 2 A（晶體管）；四個電壓組；每組 8 A；可設置診斷功能；可設置輸出替代值
DQ 8x230VAC/2A ST;
數字量輸出模塊，8 通道 230 VAC / 2 A（晶體管）；八個電壓組；每組 2 A；可設置診斷功能；可設置輸出替代值
DQ 8x230VAC/5A ST;
帶有 8 點輸出的數字量輸出模塊，230 V AC/5 A（繼電器）；8 個電壓組；每組 5 A；可設置輸出的替代值

提供了以下寬度為 25 mm 的數字量輸出模塊：

DQ 16x24VDC/0.5A BA;
帶有 16 個通道的數字量輸出模塊，24 VDC/0.5 A（晶體管）；源型輸出；兩個電壓組 4A
DQ 32x24VDC/0.5A BA;
帶有 16 個通道的數字量輸出模塊，24 VDC/0.5 A（晶體管）；源型輸出；四個電壓組；每組 4 A

設計

用一個螺絲安裝在 S7-1500 安裝導軌上
35 mm 模塊采用螺釘型端子或推入式端子的標準化 40 針前連接器（不能用于 25 mm 模塊）
25 mm 模塊采用推入式端子的標準化 40 針前連接器（不能用于 35 mm 模塊）
標準化、協調型前連接器針腳分配，更便于接線
可連接芯線截面積0.25 mm² 至 1.5 mm²（AWG24 至 16）
集成式電壓橋接件，用于靈活形成電壓組(僅 35 mm 模塊)
前連接器的預接線位置
前蓋帶有可擴充的電纜室，即使*接線時也如此
模塊正面的清晰標簽
- 模塊類型
- 訂貨號
- 硬件和固件型號
- 通道編號標簽
- 電纜連接圖

含在供貨范圍之內：

用于手工貼標簽的一個標簽條
一個 U 型連接器
印制有文字的前門
前連接器（(僅 25 mm 模塊）

功能

統一的顯示和診斷方式：
- 故障（紅色 LED）和運行（綠色 LED）模塊狀態顯示
- 用于信號狀態日志的信號狀態顯示。"0" 和日志。"1"（綠色 LED）或短路指示（紅色 LED）
- 顯示 24 V DC 電源電壓（綠色 LED）
支持的功能：
- 識別和維護數據 IM0 至 IM3
- 固件更新
- 與通道有關的參數分配（* HF 模塊）
- 按通道進行診斷（* HF 模塊）
- 等時同步模式（取決于模塊）
- 可以為輸出設置替換值（*于 35 mm 模塊）

技術規范

Article number	6ES7522-1BH01-0AB0	6ES7522-1BL01-0AB0	6ES7522-1BF00-0AB0	6ES7522-5EH00-0AB0
	S7-1500, DQ 16X24V DC/0.5A HF	S7-1500, DQ 32X24VDC/0.5A HF	S7-1500, DQ 8X24VDC/2A HF	S7-1500, DQ 16X24...48VUC/125VDC/0.5A ST
General information
Product type designation	DQ 16x24VDC/0.5A HF	DQ 32x24VDC/0.5A HF	DQ 8x24VDC/2A HF
HW functional status	FS01	FS01	FS01	FS01
Firmware version	V1.0.0	V1.0.0	V2.1.0	V1.0.0
● FW update possible	Yes		Yes	Yes
Product function
● I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated as of version	V13 SP1 / -	V13 SP1 / -	V13 SP1 / -	V13 SP1 / -
● STEP 7 configurable/integrated as of version			V5.5 SP3 / -	V5.5 SP3 / -
● PROFIBUS as of GSD version/GSD revision	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1
● PROFINET as of GSD version/GSD revision	V2.3 / -	V2.3 / -	V2.3 / -	V2.3 / -
Operating mode
● DQ	Yes	Yes	Yes	Yes
● DQ with energy-saving function	No	No	Yes; with an application	No
● PWM	No	No	Yes	No
● Oversampling	No	No	No	No
● MSO	Yes	Yes	Yes	Yes
Supply voltage
Rated value (DC)	24 V	24 V	24 V
permissible range, lower limit (DC)	20.4 V	20.4 V	20.4 V
permissible range, upper limit (DC)	28.8 V	28.8 V	28.8 V
Reverse polarity protection	Yes; through internal protection with 7 A per group	Yes; through internal protection with 7 A per group	Yes; through internal protection with 10 A per group
Input current
Current consumption, max.	30 mA	60 mA	40 mA; 20 mA per group, no output is activated.
Output voltage
Rated value (DC)	24 V	24 V	24 V	24 V; 48 V, 125 V
Rated value (AC)				24 V; 48 V (50 - 60 Hz)
Power
Power available from the backplane bus	1.1 W	1.1 W	0.9 W	2 W
Power loss
Power loss, typ.	2 W	3.5 W	5.6 W; 6.8 W for PWM operation	3.8 W
Digital outputs
Type of digital output	Transistor	Transistor	Transistor	Transistor
Number of digital outputs	16	32	8	16
Current-sinking				Yes
Current-sourcing	Yes	Yes	Yes	Yes
Short-circuit protection	Yes; Clocked electronically	Yes; Clocked electronically	Yes
● Response threshold, typ.	1 A	1 A	3 A
Limitation of inductive shutdown voltage to	L+ (-53 V)	L+ (-53 V)	-17 V	200 V (suppressor diode)
Controlling a digital input	Yes	Yes	Yes	Yes
Digital output functions, parameterizable
● Freely usable digital output			Yes
● PWM output			Yes
— Number, max.			2
— Cycle duration, parameterizable			Yes; 2 ... 100 ms continuous
— ON period, min.			0 %
— ON period, max.			100 %
— Resolution of the duty cycle			0.1 %
— Minimum pulse duration			300 µs
Switching capacity of the outputs
● with resistive load, max.	0.5 A	0.5 A		0.5 A
● on lamp load, max.	5 W	5 W	10 W	40 W; At 125 V DC, 10 W at 48 V UC, 5 W at 24 V UC
Load resistance range
● lower limit	48 ?	48 ?	12 ?
● upper limit	12 k?	12 k?	4 k?
Output voltage
● for signal "1", min.	L+ (-0.8 V)	L+ (-0.8 V)	L+ (-0.8 V)	L+ (-1.0 V)
Output current
● for signal "1" rated value	0.5 A	0.5 A	2 A	0.5 A
● for signal "1" permissible range, max.	0.5 A	0.5 A	2.4 A; Note derating specification for PWM operation	0.6 A
● for signal "0" residual current, max.	0.5 mA	0.5 mA	0.5 mA
Output delay with resistive load
● "0" to "1", typ.			80 µs
● "0" to "1", max.	100 µs	100 µs	100 µs	5 ms
● "1" to "0", typ.			300 µs
● "1" to "0", max.	500 µs	500 µs	500 µs	5 ms
Parallel switching of two outputs
● for logic links	Yes	Yes	Yes	Yes
● for uprating	No	No	No	No
● for redundant control of a load	Yes	Yes	Yes	Yes
Switching frequency
● with resistive load, max.	100 Hz	100 Hz	100 Hz; With PWM operation: 500 Hz	25 Hz
● with inductive load, max.	0.5 Hz; According to IEC 60947-5-1, DC-13	0.5 Hz; According to IEC 60947-5-1, DC-13	0.5 Hz; According to IEC 60947-5-1, DC-13; max. 500 Hz with PWM operation only with external circuit; see additional description in the manual	0.5 Hz
● on lamp load, max.	10 Hz	10 Hz	10 Hz	10 Hz
Total current of the outputs
● Current per channel, max.	0.5 A; see additional description in the manual	0.5 A; see additional description in the manual	2 A; see additional description in the manual	0.5 A
● Current per group, max.	4 A; see additional description in the manual	4 A; see additional description in the manual	8 A; see additional description in the manual	0.5 A
● Current per module, max.	8 A; see additional description in the manual	16 A; see additional description in the manual	16 A; see additional description in the manual	8 A
Cable length
● shielded, max.	1 000 m	1 000 m	1 000 m	1 000 m
● unshielded, max.	600 m	600 m	600 m	600 m
Isochronous mode
Isochronous operation (application synchronized up to terminal)	Yes	Yes	No	No
Execution and activation time (TCO), min.	70 µs	70 µs
Bus cycle time (TDP), min.	250 µs	250 µs
Interrupts/diagnostics/status information
Diagnostics function	Yes	Yes	Yes	No
Substitute values connectable	Yes	Yes	Yes	Yes
Alarms
● Diagnostic alarm	Yes	Yes	Yes	No
Diagnostic messages
● Monitoring the supply voltage	Yes	Yes	Yes	No
● Wire-break	Yes	Yes	No	No
● Short-circuit	Yes	Yes	Yes	No
● Group error	Yes	Yes	Yes
Diagnostics indication LED
● RUN LED	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
● ERROR LED	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED
● Monitoring of the supply voltage (PWR-LED)	Yes; Green LED	Yes; Green LED	Yes; Green LED	No
● Channel status display	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
● for channel diagnostics	Yes; Red LED	Yes; Red LED	Yes; Red LED	No
● for module diagnostics	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED
Potential separation
Potential separation channels
● between the channels	No	No	No	Yes
● between the channels, in groups of	8	8	4	1
● between the channels and backplane bus	Yes	Yes	Yes	Yes
Permissible potential difference
between different circuits				125 V DC/48 V AC
Isolation
Isolation tested with	707 V DC (type test)	707 V DC (type test)	707 V DC (type test)	2 000 V DC
Ambient conditions
Ambient temperature during operation
● horizontal installation, min.	0 °C			0 °C
● horizontal installation, max.	60 °C			60 °C
● vertical installation, min.	0 °C			0 °C
● vertical installation, max.	60 °C			40 °C
Decentralized operation
Prioritized startup	Yes	Yes	Yes	Yes
Dimensions
Width	35 mm	35 mm	35 mm	35 mm
Height	147 mm	147 mm	147 mm	147 mm
Depth	129 mm	129 mm	129 mm	129 mm
Weights
Weight, approx.	230 g	280 g	240 g	230 g

Article number	6ES7522-5HF00-0AB0	6ES7522-5HH00-0AB0	6ES7522-5FF00-0AB0	6ES7522-5FH00-0AB0
	S7-1500, DQ 8X230VAC/5A ST (RELAY)	S7-1500, DQ 16X230VAC/2A ST (RELAY)	S7-1500, DQ 8X230VAC/2A ST (TRIAC)	S7-1500, DQ 16X230VAC/1A ST (TRIAC)
General information
Product type designation			DQ 8x230 V AC/2A ST (triac)	DQ 16x230VAC/1A ST (Triac)
HW functional status	FS01	FS01	FS01	FS01
Firmware version	V2.0.0	V1.0.0	V2.0.0	V1.0.0
● FW update possible	Yes	Yes	Yes	Yes
Product function
● I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated as of version	V12 / V12	V13 SP1 / -	V12 / V12	V13 SP1 / -
● STEP 7 configurable/integrated as of version	V5.5 SP3 / -	V5.5 SP3 / -	V5.5 SP3 / -	V5.5 SP3 / -
● PROFIBUS as of GSD version/GSD revision	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1
● PROFINET as of GSD version/GSD revision	V2.3 / -	V2.3 / -	V2.3 / -	V2.3 / -
Operating mode
● DQ	Yes	Yes	Yes	Yes
● DQ with energy-saving function	No	No	No	No
● PWM	No	No	No	No
● Oversampling	No	No	No	No
● MSO	Yes	Yes	Yes	Yes
Supply voltage
Rated value (DC)	24 V	24 V
permissible range, lower limit (DC)	20.4 V	20.4 V
permissible range, upper limit (DC)	28.8 V	28.8 V
Reverse polarity protection	Yes	Yes
Input current
Current consumption, max.	80 mA	150 mA
Output voltage
Rated value (AC)	230 V; 24 V DC to 120 V DC / 24 V AC to 230 V AC	230 V; 24 V DC to 120 V DC / 24 V AC to 230 V AC	230 V; 120/230V AC, 50/60 Hz	230 V; 120/230V AC, 50/60 Hz
Power
Power available from the backplane bus	0.8 W	0.8 W	0.9 W	1.2 W
Power loss
Power loss, typ.	5 W	5 W	10.8 W	11.1 W
Digital outputs
Type of digital output	Relays	Relays	Triac	Triac
Number of digital outputs	8	16	8	16
Current-sinking	Yes	Yes		Yes
Current-sourcing	Yes	Yes	Yes	Yes
Short-circuit protection	No	No	No	No
Controlling a digital input	possible	Yes
Switching capacity of the outputs
● with resistive load, max.			2 A	1 A
● on lamp load, max.	1 500 W; 10 000 operating cycles	50 W (230 V AC), 5 W (24 V DC)	50 W	50 W
● Low energy/fluorescent lamps with electronic control gear	10x 58 W (25 000 operating cycles)
● Fluorescent tubes, conventionally compensated	1x 58 W (25 000 operating cycles)
● Fluorescent tubes, uncompensated	10x 58 W (25 000 operating cycles)
Output voltage
● for signal "1", min.			L1 (-1.5 V) at maximum output current; L1 (-8.5 V) at minimum output current	L1 (-1.5 V) at maximum output current; L1 (-8.5 V) at minimum output current
Output current
● for signal "1" rated value	5 A	2 A	2 A	1 A
● for signal "1" permissible range, min.	5 mA; 10 V	10 mA; 10 V	10 mA	10 mA
● for signal "1" permissible range, max.	8 A; thermal continuous current	2 A; thermal continuous current	15 A; max. 1 AC cycle	15 A; max. 1 AC cycle
● for signal "0" residual current, max.	0 A	0 A	2 mA	2 mA
Output delay with resistive load
● "0" to "1", max.			1 AC cycle	1 AC cycle
● "1" to "0", max.			1 AC cycle	1 AC cycle
Parallel switching of two outputs
● for logic links	Yes	Yes	No	No
● for uprating	No	No	No	No
● for redundant control of a load	Yes	Yes	Yes	Yes
Switching frequency
● with resistive load, max.	2 Hz	1 Hz	10 Hz	10 Hz
● with inductive load, max.	0.5 Hz	0.5 Hz	0.5 Hz	0.5 Hz
● on lamp load, max.	2 Hz	1 Hz	1 Hz	1 Hz
Total current of the outputs
● Current per channel, max.	8 A; see additional description in the manual	2 A; see additional description in the manual	2 A; see additional description in the manual	1 A; see additional description in the manual
● Current per group, max.	8 A; see additional description in the manual	4 A; see additional description in the manual	2 A; see additional description in the manual	2 A; see additional description in the manual
● Current per module, max.	64 A; see additional description in the manual	32 A; see additional description in the manual	10 A; see additional description in the manual	10 A; see additional description in the manual
Relay outputs
● Number of relay outputs	8	16
● Rated supply voltage of relay coil L+ (DC)	24 V	24 V
● Current consumption of relays (coil current of all relays), typ.	80 mA	150 mA
● external protection for relay outputs	With miniature circuit breaker with characteristic B for: cos φ 1.0: 600 A cos φ 0.5 ... 0.7: 900 A with 8 A Diazed fuse: 1000 A	Miniature circuit breaker B10 / B16
● Contact connection (internal)	No	No
● Size of motor starters according to NEMA, max.	5	5
● Number of operating cycles, max.	4 000 000; see additional description in the manual	see additional description in the manual
● Relay approved acc. to UL 508	Yes; 250 V AC/5 A g.p.; 120 V AC TV-4 tungsten; A300, R300	No
Switching capacity of contacts
— with inductive load, max.	see additional description in the manual	2 A; see additional description in the manual
— with resistive load, max.	see additional description in the manual	2 A; see additional description in the manual
Triac outputs
● Size of motor starters according to NEMA, max.			5	4
Cable length
● shielded, max.	1 000 m	1 000 m	1 000 m	1 000 m
● unshielded, max.	600 m	600 m	600 m	600 m
Isochronous mode
Isochronous operation (application synchronized up to terminal)	No	No	No	No
Interrupts/diagnostics/status information
Diagnostics function	Yes	Yes	No	No
Substitute values connectable	Yes	Yes	Yes	Yes
Alarms
● Diagnostic alarm	Yes	Yes	No	No
Diagnostic messages
● Monitoring the supply voltage	Yes	Yes	No	No
● Wire-break	No	No	No	No
● Short-circuit	No	No	No	No
Diagnostics indication LED
● RUN LED	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
● ERROR LED	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED
● Monitoring of the supply voltage (PWR-LED)	Yes; Green LED	Yes; Green LED	No	No
● Channel status display	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
● for channel diagnostics	No	No	No	No
● for module diagnostics	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED
Potential separation
Potential separation channels
● between the channels	Yes; Switching of different phases permitted	No	Yes	No
● between the channels, in groups of	1	2	1	2
● between the channels and backplane bus	Yes	Yes	Yes	Yes
● Between the channels and load voltage L+	Yes	Yes
● Between the channels and load voltage L1			Yes
Permissible potential difference
between different circuits	250 V AC between the channels and the supply voltage L+; 250 V AC between the channels and the backplane bus; 500 V AC between the channels	250 V AC between the channels and the supply voltage L+; 250 V AC between the channels and the backplane bus; 500 V AC between the channels	250 V AC between the channels and the backplane bus; 500 V AC between the channels	250 V AC between the channels and the backplane bus; 500 V AC between the channels
Isolation
Isolation tested with	Between channels: 3 100 V DC; between channels backplane bus: 3 100 V DC; between L+ and backplane bus: 707 V DC (type test)	Between channels: 3 100 V DC; between channels backplane bus: 3 100 V DC; between L+ and backplane bus: 707 V DC (type test)	3 100 V DC	3 100 V DC
Ambient conditions
Ambient temperature during operation
● horizontal installation, min.	0 °C	0 °C	0 °C	0 °C
● horizontal installation, max.	60 °C	60 °C	60 °C	60 °C
● vertical installation, min.	0 °C	0 °C	0 °C	0 °C
● vertical installation, max.	40 °C	40 °C	40 °C	60 °C
Decentralized operation
Prioritized startup	Yes	Yes	Yes	Yes
Dimensions
Width	35 mm	35 mm	35 mm	35 mm
Height	147 mm	147 mm	147 mm	147 mm
Depth	129 mm	129 mm	129 mm	129 mm
Weights
Weight, approx.	350 g	350 g	290 g	310 g

Article number	6ES7522-1BH10-0AA0	6ES7522-1BL10-0AA0
	S7-1500, DQ 16X24VDC/0.5A BA	S7-1500, DQ 32X24VDC/0.5A BA
General information
Product type designation	DQ 16x24VDC/0.5A BA	DQ 32x24VDC/0.5A BA
HW functional status	FS01	FS01
Firmware version	V1.0.0	V1.0.0
● FW update possible	Yes	Yes
Product function
● I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated as of version	V13 / V13	V13 / V13
● STEP 7 configurable/integrated as of version	V5.5 SP3 / -	V5.5 SP3 / -
● PROFIBUS as of GSD version/GSD revision	V1.0 / V5.1	V1.0 / V5.1
● PROFINET as of GSD version/GSD revision	V2.3 / -	V2.3 / -
Operating mode
● DQ	Yes	Yes
● DQ with energy-saving function	No	No
● PWM	No	No
● Oversampling	No	No
● MSO	Yes	Yes
Supply voltage
Rated value (DC)	24 V	24 V
permissible range, lower limit (DC)	20.4 V	20.4 V
permissible range, upper limit (DC)	28.8 V	28.8 V
Reverse polarity protection	Yes; through internal protection with 7 A per group	Yes; through internal protection with 7 A per group
Input current
Current consumption, max.	30 mA	60 mA
Output voltage
Rated value (DC)	24 V	24 V
Power
Power available from the backplane bus	1.15 W	1.15 W
Power loss
Power loss, typ.	2.2 W	3.8 W
Digital outputs
Type of digital output	Transistor	Transistor
Number of digital outputs	16	32
Current-sourcing	Yes	Yes
Short-circuit protection	Yes	Yes
● Response threshold, typ.	1 A	1 A
Limitation of inductive shutdown voltage to	L+ (-53 V)	L+ (-53 V)
Controlling a digital input	Yes	Yes
Switching capacity of the outputs
● with resistive load, max.	0.5 A	0.5 A
● on lamp load, max.	5 W	5 W
Load resistance range
● lower limit	48 ?	48 ?
● upper limit	12 k?	12 k?
Output voltage
● for signal "1", min.	L+ (-0.8 V)	L+ (-0.8 V)
Output current
● for signal "1" rated value	0.5 A	0.5 A
● for signal "1" permissible range, max.	0.5 A	0.5 A
● for signal "0" residual current, max.	0.5 mA	0.5 mA
Output delay with resistive load
● "0" to "1", max.	100 µs	100 µs
● "1" to "0", max.	500 µs	500 µs
Parallel switching of two outputs
● for logic links	Yes	Yes
● for uprating	No	No
● for redundant control of a load	Yes	Yes
Switching frequency
● with resistive load, max.	100 Hz	100 Hz
● with inductive load, max.	0.5 Hz; According to IEC 60947-5-1, DC-13	0.5 Hz; According to IEC 60947-5-1, DC-13
● on lamp load, max.	10 Hz	10 Hz
Total current of the outputs
● Current per channel, max.	0.5 A; see additional description in the manual	0.5 A; see additional description in the manual
● Current per group, max.	4 A; see additional description in the manual	4 A; see additional description in the manual
● Current per module, max.	8 A; see additional description in the manual	16 A; see additional description in the manual
Cable length
● shielded, max.	1 000 m	1 000 m
● unshielded, max.	600 m	600 m
Isochronous mode
Isochronous operation (application synchronized up to terminal)	No	No
Interrupts/diagnostics/status information
Diagnostics function	No	No
Substitute values connectable	No	No
Alarms
● Diagnostic alarm	No	No
Diagnostic messages
● Monitoring the supply voltage	No	No
● Wire-break	No	No
● Short-circuit	No	No
● Group error	No	No
Diagnostics indication LED
● RUN LED	Yes; Green LED	Yes; Green LED
● ERROR LED	Yes; Red LED	Yes; Red LED
● Monitoring of the supply voltage (PWR-LED)	Yes; Green LED	Yes; Green LED
● Channel status display	Yes; Green LED	Yes; Green LED
● for channel diagnostics	No	No
● for module diagnostics	No	No
Potential separation
Potential separation channels
● between the channels	No	No
● between the channels, in groups of	8	8
● between the channels and backplane bus	Yes	Yes
Isolation
Isolation tested with	707 V DC (type test)	707 V DC (type test)
Decentralized operation
Prioritized startup	Yes	Yes
Dimensions
Width	25 mm	25 mm
Height	147 mm	147 mm
Depth	129 mm	129 mm
Weights
Weight, approx.	230 g	280 g
Other
Note:	Supplied incl. 40-pole push-in front connectors	Supplied incl. 40-pole push-in front connectors