西門子972-0BA41-0XA0 西門子972-0BA41-0XA0 0

• 公司名稱：上海朔川電氣設備有限公司
• 聯 系 人：吉夢琪
• ：
• 地址：上海市金山區涇波路129號
• ：2840735331

• SIPLUS CPU 417-4 訂貨數據   附件   產品信息   組態工具 跳轉到 概述 應用 設計 功能 技術規范 概述 強大的 SIMATIC S7-400 CPU 適用于對性能要求很高的工廠 帶兩個 IF 模塊的插槽 注： SIPLUS extreme 產品基于 SIMATIC 標準產品。此處列出的內容來自相關的標準產品。添加了特定 SIPLUS extreme 信息。 有關 SIPLUS 的技術文檔，可訪問： http://www.siemens.de/siplus-extreme 應用 The CPU 417-4 is the most powerful SIMATIC S7-400 CPU. The integral PROFIBUS DP interfaces permit direct connection to the PROFIBUS DP fieldbus as master or slave. Two further DP master systems can be connected via the IF 964-DP interface submodules. Note: Only the interface module 6ES7 964-2AA04-0AB0 can be used. 設計 CPU 417-4 的特性： 強大的處理器： CPU 執行每條二進制指令時間僅為 0.018 µs。 32 MB 工作存儲器（程序和數據各 16 MB）； 快速工作存儲器用于對于執行十分重要的用戶程序部分。 可靈活擴展： zui多 262 144 點數字量輸入/輸出和 16 384點模擬量輸入/輸出 MPI 多點接口： 通過 MPI，可方便地將zui多 32 個站聯成網絡，數據傳輸速率可高達 12 Mbit/s。該 CPU 可與通信總線 (C-bus) 和 MPI 的站之間建立zui多 44 個連接。 注意： 如果 PROFIBUS DP 接口和 MPI 接口同時運行，那么只能將以下總線連接器連接到 MPI 接口： 帶插口：6ES7 972-0BB42-0XA0 不帶插口：6ES7 972-0BA42-0XA0 模式選擇開關： 撥位開關設計。 診斷緩沖區： zui后的 120 個故障和中斷事件保存在一個環形緩沖器中，用于進行診斷（可擴展）。 實時時鐘： CPU 的診斷報警帶有日期和時間標記。 存儲卡： 用于擴展內置裝載存儲器。存儲在裝載存儲器中的信息包括 S7?400 參數數據以及程序，因此需要 2 倍的存儲空間。其結果是： 內置的裝載存儲器不能滿足大程序量的要求，因此需要存儲卡。 可使用 RAM 和 FEPROM 卡（FEPROM 卡用于保持性存儲）。 PROFIBUS DP 接口： 通過 PROFIBUS DP 主站接口，可以實現分布式自動化組態，從而提高了速度，便于使用。對用戶來說,分布式 I/O 單元可作為一個集中式單元來處理（相同的組態、編址和編程）。 混合組態：SIMATIC S5，SIMATIC S7 為 PROFIBUS 主站，符合 EN 50170 標準。 注： 當同時使用 PROFIBUS DP 和 MPI 接口時，只能將下列總線連接器連接到 MPI 接口： 帶插口：6ES7 972-0BB42-0XA0 不帶插口：6ES7 972-0BA42-0XA0 兩個附加插槽： 可用 IF 964-DP 接口子模塊連接兩個附加的 PROFIBUS DP主站系統。   Block protection:  a password concept also protects the user program from unauthorized access Integrated HMI services:  The user only has to specify the source and destination of the data with HMI devices. The data are then transported cyclically and automatically by the system. Integrated communication functions: PG/OP communication Global data communication S7 standard communication S7 communication Configurable Attributes The STEP 7 tool "Hardware configuration" can be used to program the properties and response of the S7-400 including the CPUs, e.g. Multipoint interface MPI: Definition of node addresses Startup/cycle behavior Stipulation of the maximum cycle time and communication load Address allocation:  Addressing of I/O modules Retentive area:  Definition of the number of retentive bit memories, counters, timers, data blocks, and clock memories Size of the process image, local data Length of the diagnostics buffer Protection level:  Definition of access authorizations to program and data System diagnostics:  Definition of the handling and scope of diagnostics messages Timed interrupts:  Setting of periods Configuring Reporting functions Status and fault indicators:  LEDs indicate internal and external faults and operating modes such RUN, STOP, restart, test function, etc. Test functions:  The PG can be used to display signal states in program execution, modify process tags irrespective of the user program, read out the contents of stack memories, run separate program steps and inhibit program components. Information functions:  The PG can be used to provide the user with information about the memory capacity and operating mode of the CPU, and the current utilization of the working and load memories. 技術規范 Article number 6AG1417-4XT07-7AB0   SIPLUS S7-400 CPU 417-4 V7 General information   Product type designation CPU 417-4 Hardware product version 01 Firmware version V7.0 Engineering with   ● Programming package STEP 7 V5.4 or higher with HSP 261 CiR – Configuration in RUN   CiR synchronization time, basic load 60 ms CiR synchronization time, time per I/O byte 7 µs Supply voltage   Rated value (DC)   ● 24 V DC No; Power supply via system power supply Input current   from backplane bus 5 V DC, typ. 1.3 A from backplane bus 5 V DC, max. 1.6 A from backplane bus 24 V DC, max. 600 mA; 150 mA per DP interface from interface 5 V DC, max. 90 mA; At each DP interface Power loss   Power loss, typ. 6.5 W Power loss, max. 8 W Memory   Type of memory RAM Work memory   ● integrated 32 Mbyte ● integrated (for program) 16 Mbyte ● integrated (for data) 16 Mbyte ● expandable No Load memory   ● expandable FEPROM Yes; with Memory Card (FLASH) ● expandable FEPROM, max. 64 Mbyte ● integrated RAM, max. 1 Mbyte ● expandable RAM Yes; with Memory Card (RAM) ● expandable RAM, max. 64 Mbyte Backup   ● present Yes ● with battery Yes; all data ● without battery No Battery   Backup battery   ● Backup current, typ. 225 µA; up to 40 °C ● Backup current, max. 1 275 µA ● Backup time, max. See reference manual, module data, Chapter 3.3 ● Feeding of external backup voltage to CPU 5 V DC to 15 V DC CPU processing times   for bit operations, typ. 7.5 ns for word operations, typ. 7.5 ns for fixed point arithmetic, typ. 7.5 ns for floating point arithmetic, typ. 15 ns CPU-blocks   DB   ● Number, max. 16 000; Number range: 1 to 16000 ● Size, max. 64 kbyte FB   ● Number, max. 8 000; Number range: 0 to 7999 ● Size, max. 64 kbyte FC   ● Number, max. 8 000; Number range: 0 to 7999 ● Size, max. 64 kbyte OB   ● Number, max. see instruction list ● Size, max. 64 kbyte ● Number of free cycle OBs 1; OB 1 ● Number of time alarm OBs 8; OB 10-17 ● Number of delay alarm OBs 4; OB 20-23 ● Number of cyclic interrupt OBs 9; OB 30-38 (shortest cycle that can be set = 500 µs) ● Number of process alarm OBs 8; OB 40-47 ● Number of DPV1 alarm OBs 3; OB 55-57 ● Number of isochronous mode OBs 4; OB 61-64 ● Number of multicomputing OBs 1; OB 60 ● Number of background OBs 1; OB 90 ● Number of startup OBs 3; OB 100-102 ● Number of asynchronous error OBs 9; OB 80-88 ● Number of synchronous error OBs 2; OB 121, 122 Nesting depth   ● per priority class 24 ● additional within an error OB 2 Counters, timers and their retentivity   S7 counter   ● Number 2 048 Retentivity   — adjustable Yes — lower limit 0 — upper limit 2 047 — preset Z 0 to Z 7 Counting range   — lower limit 0 — upper limit 999 IEC counter   ● Number Unlimited (limited only by RAM capacity) S7 times   ● Number 2 048 Retentivity   — adjustable Yes — lower limit 0 — upper limit 2 047 — preset No times retentive Time range   — lower limit 10 ms — upper limit 9 990 s IEC timer   ● present Yes ● Type SFB ● Number Unlimited (limited only by RAM capacity) Data areas and their retentivity   retentive data area in total Total working and load memory (with backup battery) Flag   ● Number, max. 16 kbyte; Size of bit memory address area ● Retentivity available Yes ● Retentivity preset MB 0 to MB 15 ● Number of clock memories 8; in 1 memory byte Data blocks   ● Number, max. 16 000; Number range: 1 to 16000 ● Size, max. 64 kbyte Local data   ● adjustable, max. 64 kbyte ● preset 32 kbyte Address area   I/O address area   ● Inputs 16 kbyte ● Outputs 16 kbyte of which distributed   — MPI/DP interface, inputs 2 kbyte — MPI/DP interface, outputs 2 kbyte — DP interface, inputs 8 kbyte — DP interface, outputs 8 kbyte Process image   ● Inputs, adjustable 16 kbyte ● Outputs, adjustable 16 kbyte ● Inputs, default 1 024 byte ● Outputs, default 1 024 byte ● consistent data, max. 244 byte ● Access to consistent data in process image Yes Subprocess images   ● Number of subprocess images, max. 15 Digital channels   ● Inputs 131 072 — of which central 131 072 ● Outputs 131 072 — of which central 131 072 Analog channels   ● Inputs 8 192 — of which central 8 192 ● Outputs 8 192 — of which central 8 192 Hardware configuration   Number of expansion units, max. 21 connectable OPs 119 Multicomputing Yes; 4 CPUs max. (with UR1 or UR2) Interface modules   ● Number of connectable IMs (total), max. 6 ● Number of connectable IM 460s, max. 6 ● Number of connectable IM 463s, max. 4; IM 463-2 Number of DP masters   ● integrated 2 ● via CP 10; CP 443-5 Extended ● via IM 467 4 ● Mixed mode IM + CP permitted No; IM 467 cannot be used jointly with CP 443-5 Ext. or CP 443-1 in PROFINET IO mode ● via interface module 2 ● Number of pluggable S5 modules (via adapter capsule in central device), max. 6 Number of IO Controllers   ● integrated 0 ● via CP 4; Max. 4 in the central controller; no mixed operation of different CP 443-1 types in PROFINET IO mode Number of operable FMs and CPs (recommended)   ● FM Limited by number of slots and number of connections ● CP, PtP CP 440: Limited by number of slots; CP 441: limited by number of connections ● PROFIBUS and Ethernet CPs 14; Of which 10 CPs max. or IMs as DP master, 4 PROFINET controller maximum Slots   ● required slots 2 Time of day   Clock   ● Hardware clock (real-time) Yes ● retentive and synchronizable Yes ● Resolution 1 ms ● Deviation per day (buffered), max. 1.7 s; Power off ● Deviation per day (unbuffered), max. 8.6 s; For power On Operating hours counter   ● Number 16 ● Number/Number range 0 to 15 ● Range of values SFCs 2, 3 and 4: 0 to 32767 hours SFC 101: 0 to 2^31 - 1 hours ● Granularity 1 hour ● retentive Yes Clock synchronization   ● supported Yes ● to MPI, master Yes ● to MPI, slave Yes ● to DP, master Yes ● to DP, slave Yes ● in AS, master Yes ● in AS, slave Yes ● on Ethernet via NTP No; Via CP ● to IF 964 DP Yes Time difference in system when synchronizing via   ● MPI, max. 200 ms Interfaces   Interfaces/bus type 1 x MPI/PROFIBUS DP, 1 x PROFIBUS DP, 2 x PROFIBUS DP (optionally pluggable) Number of RS 485 interfaces 2; Combined MPI / PROFIBUS DP and PROFIBUS DP Number of other interfaces 2; PROFIBUS DP with IF 964-DP (plug-in option; MLFB: 6ES7964-2AA04-0AB0) 1. Interface   Interface type Integrated Physics RS 485 / PROFIBUS + MPI Isolated Yes Power supply to interface (15 to 30 V DC), max. 150 mA Number of connection resources MPI: 44, DP: 32 Functionality   ● MPI Yes ● PROFIBUS DP master Yes ● PROFIBUS DP slave Yes MPI   ● Number of connections 44; If a diagnostics repeater is used on the line, the number of connection resources on the line is reduced by 1 ● Transmission rate, max. 12 Mbit/s Services   — PG/OP communication Yes — Routing Yes — Global data communication Yes — S7 basic communication Yes — S7 communication Yes — S7 communication, as client Yes — S7 communication, as server Yes DP master   ● Number of connections, max. 32; If a diagnostics repeater is used on the line, the number of connection resources on the line is reduced by 1 ● Transmission rate, max. 12 Mbit/s ● Number of DP slaves, max. 32 Services   — PG/OP communication Yes — Routing Yes; S7 routing — Global data communication No — S7 basic communication Yes — S7 communication Yes — S7 communication, as client Yes — S7 communication, as server Yes — Equidistance Yes — Isochronous mode Yes — SYNC/FREEZE Yes — Activation/deactivation of DP slaves Yes — Direct data exchange (slave-to-slave communication) Yes — DPV1 Yes Address area   — Inputs, max. 2 kbyte — Outputs, max. 2 kbyte User data per DP slave   — User data per DP slave, max. 244 byte — Inputs, max. 244 byte — Outputs, max. 244 byte — Slots, max. 244 — per slot, max. 128 byte DP slave   ● Number of connections 32 ● GSD file http://support.automation.siemens.com/WW/view/en/113652 ● Transmission rate, max. 12 Mbit/s ● automatic baud rate search No ● Address area, max. 32; Virtual slots ● User data per address area, max. 32 byte — of which consistent, max. 32 byte Services   — PG/OP communication Yes; with interface active — S7 routing Yes; with interface active — Global data communication No — S7 basic communication No — S7 communication Yes — S7 communication, as client Yes — S7 communication, as server Yes — Direct data exchange (slave-to-slave communication) No — DPV1 No Transfer memory   — Inputs 244 byte — Outputs 244 byte 2. Interface   Interface type Integrated Physics RS 485 / PROFIBUS Isolated Yes Power supply to interface (15 to 30 V DC), max. 150 mA Number of connection resources 32 Functionality   ● PROFIBUS DP master Yes ● PROFIBUS DP slave Yes DP master   ● Number of connections, max. 32 ● Transmission rate, max. 12 Mbit/s ● Number of DP slaves, max. 125 Services   — PG/OP communication Yes — Routing Yes; S7 routing — Global data communication No — S7 basic communication Yes — S7 communication Yes — S7 communication, as client Yes — S7 communication, as server Yes — Equidistance Yes — Isochronous mode Yes — SYNC/FREEZE Yes — Activation/deactivation of DP slaves Yes — Direct data exchange (slave-to-slave communication) Yes — DPV1 Yes Address area   — Inputs, max. 8 kbyte — Outputs, max. 8 kbyte User data per DP slave   — User data per DP slave, max. 244 byte — Inputs, max. 244 byte — Outputs, max. 244 byte — Slots, max. 244 — per slot, max. 128 byte DP slave   ● Number of connections 32 ● GSD file http://support.automation.siemens.com/WW/view/en/113652 ● Transmission rate, max. 12 Mbit/s ● Address area, max. 32 ● User data per address area, max. 32 byte — of which consistent, max. 32 byte Services   — Routing Yes; with interface active Transfer memory   — Inputs 244 byte — Outputs 244 byte 3. Interface   Interface type Pluggable interface module (IF), technical data as for 2nd interface Plug-in interface modules IF 964-DP (MLFB: 6ES7964-2AA04-0AB0) Physics RS 485 / PROFIBUS Isolated Yes Power supply to interface (15 to 30 V DC), max. 150 mA automatic detection of transmission rate No Number of connection resources 32 Functionality   ● MPI No ● PROFIBUS DP master Yes ● PROFIBUS DP slave Yes DP master   Services   — PG/OP communication Yes — Routing Yes; S7 routing — Global data communication No — S7 basic communication Yes — S7 communication Yes — S7 communication, as client Yes — S7 communication, as server Yes — Equidistance Yes — Isochronous mode Yes — SYNC/FREEZE Yes — Activation/deactivation of DP slaves Yes — Direct data exchange (slave-to-slave communication) Yes — DPV0 Yes — DPV1 Yes Address area   — Inputs, max. 8 kbyte — Outputs, max. 8 kbyte User data per DP slave   — User data per DP slave, max. 244 byte — Inputs, max. 244 byte — Outputs, max. 244 byte — Slots, max. 244 — per slot, max. 128 byte DP slave   ● Number of connections 32 ● GSD file http://support.automation.siemens.com/WW/view/en/113652 ● Transmission rate, max. 12 Mbit/s ● Address area, max. 32 ● User data per address area, max. 32 byte — of which consistent, max. 32 byte Services   — PG/OP communication Yes — S7 routing Yes; with interface active — Global data communication No — S7 basic communication No — S7 communication Yes — S7 communication, as client Yes — S7 communication, as server Yes — Direct data exchange (slave-to-slave communication) No — DPV1 No Transfer memory   — Inputs 244 byte — Outputs 244 byte 4. Interface   Interface type Pluggable interface module (IF), technical data as for 2nd interface Plug-in interface modules IF 964-DP (MLFB: 6ES7964-2AA04-0AB0) Open IE communication   ● ISO-on-TCP (RFC1006) Via CP 443-1 and loadable FB — Data length, max. 1452 bytes via CP 443-1 Adv. Isochronous mode   Isochronous operation (application synchronized up to terminal) Yes; For PROFIBUS only Equidistance Yes Number of DP masters with isochronous mode 4 User data per isochronous slave, max. 244 byte shortest clock pulse 1 ms; 0.5 ms without use of SFC 126, 127 max. cycle 32 ms Communication functions   PG/OP communication Yes ● Number of connectable OPs without message processing 119 ● Number of connectable OPs with message processing 119; When using Alarm_S/SQ and Alarm_D/DQ Data record routing Yes Global data communication   ● supported Yes ● Number of GD loops, max. 16 ● Number of GD packets, transmitter, max. 16 ● Number of GD packets, receiver, max. 32 ● Size of GD packets, max. 54 byte ● Size of GD packet (of which consistent), max. 1 variable S7 basic communication   ● supported Yes ● User data per job, max. 76 byte ● User data per job (of which consistent), max. 1 variable S7 communication   ● supported Yes ● as server Yes ● as client Yes ● User data per job, max. 64 kbyte ● User data per job (of which consistent), max. 462 byte; 1 variable S5 compatible communication   ● supported Yes; Via FC AG_SEND and AG_RECV, max. via 10 CP 443-1 or 443-5 ● User data per job, max. 8 kbyte ● User data per job (of which consistent), max. 240 byte ● Number of simultaneous AG-SEND/AG-RECV orders per CPU, max. 64/64 Standard communication (FMS)   ● supported Yes; Via CP and loadable FB Web server   ● supported No Number of connections   ● overall 120 ● usable for PG communication 119 — reserved for PG communication 1 — adjustable for PG communication, max. 0 ● usable for OP communication 119 — reserved for OP communication 1 — adjustable for OP communication, max. 0 ● usable for S7 basic communication 118 — reserved for S7 basic communication 0 — adjustable for S7 basic communication, max. 0 ● usable for S7 communication 118 — reserved for S7 communication 0 — adjustable for S7 communication, max. 0 ● usable for routing 59 — reserved for routing 0 — adjustable for routing, max. 0 S7 message functions   Number of login stations for message functions, max. 119; Max. 119 with Alarm_S/SQ and Alarm_D/DQ (OPs); max. 16 with Alarm, Alarm_8, Alarm_8P, Notify and Notify_8 (e.g. WinCC) Symbol-related messages Yes SCAN procedure Yes Block related messages Yes Process diagnostic messages Yes simultaneously active Alarm-S blocks, max. 1 000; Simultaneously active alarm_S/SQ blocks or alarm_D/DQ blocks Alarm 8-blocks Yes ● Number of instances for alarm 8 and S7 communication blocks, max. 10 000 ● preset, max. 1 200 Process control messages Yes Number of archives that can log on simultaneously (SFB 37 AR_SEND) 64 Number of messages   ● overall, max. 1 024 ● in 100 ms grid, max. 128 ● in 500 ms grid, max. 512 ● in 1000 ms grid, max. 1 024 Number of additional values   ● with 100 ms grid, max. 1 ● with 500, 1000 ms grid, max. 10 Test commissioning functions   Status block Yes; Up to 16 simultaneously Single step Yes Number of breakpoints 16 Status/control   ● Status/control variable Yes; Up to 16 variable tables ● Variables Inputs/outputs, memory bits, DBs, distributed I/Os, timers, counters ● Number of variables, max. 70; Status/control Forcing   ● Forcing Yes ● Forcing, variables Inputs, outputs, bit memories, peripheral inputs, peripheral outputs ● Number of variables, max. 512 Diagnostic buffer   ● present Yes ● Number of entries, max. 3 200 — adjustable Yes — preset 120 Service data   ● can be read out Yes Standards, approvals, certificates   CE mark Yes EAC (formerly Gost-R) Yes Ambient conditions   Ambient temperature during operation   ● min. -25 °C; = Tmin ● max. 70 °C; = Tmax Extended ambient conditions   ● relative to ambient temperature-atmospheric pressure-installation altitude Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m) Relative humidity   — With condensation, tested in accordance with IEC 60068-2-38, max. 100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation Resistance   — against biologically active substances / conformity with EN 60721-3-3 Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request — against chemically active substances / conformity with EN 60721-3-3 Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! — against mechanically active substances / conformity with EN 60721-3-3 Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! Configuration   Configuration software   ● STEP 7 Yes Programming   ● Command set see instruction list ● Nesting levels 7 ● Access to consistent data in process image Yes ● System functions (SFC) see instruction list ● System function blocks (SFB) see instruction list Programming language   — LAD Yes — FBD Yes — STL Yes — SCL Yes — CFC Yes — GRAPH Yes — HiGraph® Yes Number of simultaneously active SFCs   — DPSYC_FR 2; SFC 11; per interface — D_ACT_DP 8; SFC 12; per interface — RD_REC 8; SFC 59; per interface — WR_REC 8; SFC 58; per interface — WR_PARM 8; SFC 55; per interface — PARM_MOD 1; SFC 57; per interface — WR_DPARM 2; SFC 56; per interface — DPNRM_DG 8; SFC 13; per interface — RDSYSST 8; SFC 51 — DP_TOPOL 1; SFC 103; per interface Number of simultaneously active SFBs   — RDREC 8; SFB 52; per interface, but not more than 32 across all external interfaces — WRREC 8; SFB 53; per interface, but not more than 32 across all external interfaces Know-how protection   ● User program protection/password protection Yes ● Block encryption Yes; With S7 block Privacy Dimensions   Width 50 mm Height 290 mm Depth 219 mm Weights   Weight, approx. 900 g

  全部關于 SIPLUS CPU 417-4 產品與解決方案在線目錄與訂購系統技術信息服務與支持與合作伙伴服務項目