| | 一、概述 “鑫力”,牌采用zui先 進的銀一鋅一鋁復合邊緣加厚金屬化臘作為材料。引進*設 備、技術、嚴格按照IEC60831.1:1996標準生產,主要用于礦熱爐二次低壓無功補償,提高功率因數減少冶煉系統無功功率,降低電耗,提高電部的冶煉電壓,補償短網的電壓降等;為高能耗企業的節能降耗提供了新途徑,是國家大力*使用的節*產品。Ⅱ.
| Ⅰ. General | “Xinli” brand self-healing LV submerged-arc furnace purposed capacitor adopts the international advanced silver-zn-Al compound edge thickened metallized film. The company introduces international advanced equipment and technology, carries out production strictly according to IEC60831.1: 1996. The products are mainly applied to secondary LV reactive compensation of submerged-arc furnace, used to improve the power factor and reduce reactive power of smelting system, reduce power consumption, increase smelting voltage, compensate voltage drop of short net; it provides new ways for energy saving for high energy consumption enterprise, really is the ideal product responding to the energy saving recommendation of the government. |
| 二、型號說明 | | | 三、主要技術參數 1.使用條件:戶內-25℃~+55℃,濕度≤85%RH,海拔≤2000米 2.額定電壓:120VAC、150VAC、180VAC、200VAC、230VAC 3.額定容量:1~30Kvar 4.電容允差:0~5% 5.耐壓性能:極間2.15Un10s,極殼3000VAC 10s 6.絕緣性能:極殼500VCD 1分鐘大于1000MO 7.損耗角正切值:tg£≤0.1%(工頻額定電壓,溫度20℃) 8.zui高允許電壓:1.1Un 9.zui高允許電流:1.43In 10.自放電特性:切除電網3分鐘后,電容器端子間電壓降到75V以下 11.符合標準:GB/T12747.1-2004 IEC60831.1:11996 | Ⅲ.Main technical indexes 1. Service conditions: Indoors –25℃~+55℃, humidity ≤85%RH, altitude≤2000m 2. Rated voltage: 120VAC, 150VAC, 180VAC, 200VAC, 230VAC 3. Rated capacity: 1~30Kvar 4. Capacitance allowance: 0~5% 5. Resistance to pressure: Pole to pole 2.15Un 10s, pole to housing 3000VAC 10s 6. Insulation property: Pole to housing 500VDC 1min higher than 1000MO 7. Loss tangent: tg£≤0.1% (power frequency rated voltage, temperature 20℃) 8. Max allowable voltage: 1.1Un 9. Max allowable current: 1.43In 10. Self-discharge characteristic: Voltage among terminals of capacitor should drop to 75V below after 3min of cutting off the power grid. 11. In accordance with standards: GB/T12747.1-2004, IEC60831.1: 11996 | 四、主要特點 1.由于采用銀鋅復合邊緣加厚金屬化膜作為介質,體積小、重量輕、 性能穩定, 2.損耗低,實際值低于0.1%,所以電容器自身的能耗低,發熱小,溫升 低,工作壽命長、節能效果佳。 3.優良的自愈性能:過電壓所造成介質局部擊穿能迅速自愈,恢復正 常工作.使可靠性大為提高. 4.安全性:內裝自放電電阻和保險裝置,使用安全可靠。 5.不漏油:由于采用特種材料作為浸漬劑,常溫呈固態,熔點高于75℃ ,在使用中不漏油,避免環境污染。 | Ⅳ. Main characteristics 1. As it takes silver-zn-Al compound edge thickened metallized film as medium, it has advantages of compact volume, light weight, stable performance, etc. 2. Low loss, actual value lower than 0.1%, consequently, the capacitor itself is featured with low energy consumption, low heat, low temperature-rise, long service life, favorable energy saving efficiency. 3. Excellent self-healing property: Partial breakdown of medium caused by over-voltage can self-heal quickly, and resume normal operation. This property improves the reliability of product sharply. 4. Safety: Inner installed with self-discharge resistance and safety device, it is safe and reliable to operate. 5. Oil tight: It adopts special material as impregnant, it will be in solid state at normal temperature, melting point higher than 75℃, oil tight and avoid environmental pollution during operation. |
五、主要技術指標 MAIN TECHNIQUEINDESSIGN 型號及規格 Model & Spec. | 額定電壓 Rated voltage (Kv) | 額定容量 Rated capacity (Kvar) | 額定頻率 Rated frequency (HZ) | 額定電容 Rated capacitance (uF) | 額定電流 Rated current (A) | 外形尺寸 Outline size (mm)L*B*H | 圖號 Drawing No. | BPEMJ0.12-6-1 | 0.12 | 6 | 50 | 1327 | 50 | 215*98*250 | A | BPFMJ0.12-8-1 | 0.12 | 8 | 50 | 1769 | 66.6 | 215*98*250 | A | BPFMJ0.12-10-1 | 0.12 | 10 | 50 | 2211 | 83.3 | 310*125*210 | B | BPFMJ0.12-12-1 | 0.12 | 12 | 50 | 2654 | 100 | 310*125*260 | B | BPFMJ0.15-10-1 | 0.15 | 10 | 50 | 1415 | 66.6 | 215*98*270 | A | BPEMJ0.15-12-1 | 0.15 | 12 | 50 | 1698 | 80 | 215*98*310 | A | BPFMJ0.15-15-1 | 0.15 | 15 | 50 | 2123 | 100 | 310*125*210 | B | BPFMJ0.15-16-1 | 0.18 | 16 | 50 | 2264 | 106.6 | 310*125*230 | B | BPFMJ0.18-10-1 | 0.18 | 10 | 50 | 983 | 55.5 | 215*98*200 | A | BPFM10.18-12-1 | 0.18 | 12 | 50 | 1179 | 66.6 | 215*98*250 | A | BPFMJ0.18-15-1 | 0.18 | 15 | 50 | 1474 | 83.3 | 215*98*310 | A | BPFMJ0.18-16-1 | 0.18 | 16 | 50 | 1572 | 88.8 | 215*98*310 | A | BPFMJ0.18-20-1 | 0.18 | 20 | 50 | 1965 | 111.1 | 310*125*210 | B | BPFMJ0.2-16-1 | 0.2 | 16 | 50 | 1273 | 80 | 215*98*250 | A | BPFMJ0.2-20-1 | 0.2 | 20 | 50 | 1592 | 100 | 215*98*310 | A | BPFMJ0.2-25-1 | 0.2 | 25 | 50 | 1990 | 125 | 310*125*210 | B | BPFMJ0.23-20-1 | 0.23 | 20 | 50 | 1204 | 86.9 | 215*98*250 | A | BPFMJ0.23-25-1 | 0.23 | 25 | 50 | 1505 | 108-7 | 215*98*310 | A | BPFMJ0.23-30-1 | 0.23 | 30 | 50 | 1806 | 130.4 | 310*125*210 | B |
注:本表格所例的高度不包含接線端子的高度,A、B圖型電容器接線端子高度均為55mm Note: Height listed in this table does not contain the height of connection terminal, and height of connection terminals of A and B type capacitors is 55mm. |
|
|