騰達試驗儀器廠；

　　一、產品簡介：

　　低溫瀝青延伸度儀是檢測儀器，用于測定瀝青延度，也適用于測試改性瀝青的彈性恢復試驗。適用于測定道路石油瀝青、液體瀝青蒸餾殘留物和乳化瀝青蒸發殘留物等材料的延度。瀝青延度的試驗溫度與拉伸速率可根據要求采用，通常采用的試驗溫度為25℃，拉伸速度為5㎝／min±0.25㎝／min。當?shù)蜏夭捎?㎝／min±0.5㎝／min拉伸速度時，應在報告中注明。該產品符合GB/T4508JTJ/T0606JTJ/T0662 ASTM D 113適用于測定瀝青延度，也適用于測試改性瀝青的彈性恢復試驗。

　　Product introduction:

　　The low-temperature asphalt elongation tester is a testing instrument for measuring the ductility of asphalt,ａnd is also suitable for testing the elastic recovery test of modified asphalt.Suitable for measuring ductility of road petroleum asphalt,liquid asphalt distillation residue and emulsified asphalt evaporation residue.The test temperature and tensile rate of asphalt ductility can be adopted according to requirements.The test temperature usually used is 25℃ａnd the tensile speed is 5為/min±0.25㎝/min.When a low temperature of 1㎝/min±0.5㎝/min is used for the tensile speed,it should be indicated in the report.This product complies with GB/T4508JTJ/T0606JTJ/T0662 ASTM D 113 is suitable for measuring the ductility of asphalt,ａnd also suitable for testing the elastic recovery test of modified asphalt.

　　二、技術參數：

　　★拉伸長度：1.5m

　　★精度：1mm

　　★控溫范圍：－5～80℃

　　★精度：±0.1℃

　　★拉伸速度：10mm/Min，50mm/Min

　　★制冷功率：1.2KW，

　　★加熱功率：2KW

　　★外形尺寸：2700x800x1100mm(2m)，2300x800x1100mm(1.5m)

　　★重量：300KG

　　★電源電壓：220V

　　★功率：3KW

　　★環境溫度：5～40℃

　　★環境濕度：≦85﹪

　　Technical parameters:

　　★Stretched length:1.5m

　　★Precision:1mm

　　★Temperature control range:－5～80℃～5～80℃

　　★Accuracy:±0.1℃

　　★Stretching speed:10mm/Min,50mm/Min

　　★Refrigerating power:1.2KW

　　★Heating power:2KW

　　★Dimensions:2700x800x1100mm(2m),2300x800x1100mm(1.5m)

　　★Weight:300KG

　　★Power supply voltage:220V

　　★Power:3KW

　　★Ambient temperature:5～40℃

　　★Ambient humidity:≦85﹪

　　三、主要特點：

　　★該儀器是我公司為了適應現代公路儀器發展新研發得低成本的優質瀝青延伸度儀。

　　★制冷系統采用進口組件，設有循環系統，溫度穩定。

　　★優質不銹鋼底板，配有透明槽蓋。

　　★拉伸系統采用滾珠絲桿和直線導軌，拉伸平穩。

　　★拉伸速度由變頻器無級調速，自動高速歸位，省時帶剎車系統。

　　★屏上自動顯示伸長量，計算平均值。

　　★自動記錄試驗起始時間，試驗時間。

　　Third,the main features:

　　★This instrument is a new low-cost high-quality asphalt elongation instrument developed by our company in order to adapt to the development of modern highway instruments.

　　★The refrigeration system adopts imported components and is equipped with a circulation system to stabilize the temperature.

　　★High-quality stainless steel bottom plate with transparent cover.

　　★The stretching system adopts ball screw and linear guide to ensure stable stretching.

　　★The stretching speed is adjusted steplessly by the inverter,ａnd it automatically returns to the high speed,saving time with a braking system.

　　★The elongation is automatically displayed on the screen and the average value is calculated.

　　★Record the test start time and test time automatically.

　　四、操作規程：

　?、俦緝x器應水平放置于室內，溫度0℃~40℃，相對濕度不超過80%，無震動、無腐蝕性氣體的地面上，有良好的接地保護。

　?、谑褂们皺z查水槽內的水位，應符合測試操作規程要求，在關閉所有功能開關的情況下，接通電源，并檢查攪拌馬達，延伸動力馬達是否運轉良好。

　　③調節控溫儀到需要溫度，根據試驗要求及環境溫度需要，啟動制冷或加熱系統功能開關，同時啟動攪拌馬達。試驗時，請以水槽內溫

　　度計為準。

　?、芾鍪直D(zhuǎn)一角置空檔，再移動變速箱，將裝滿試樣的試模放置在儀器延伸端的銅圓柱銷內，推入手柄使齒輪齒合，即進入工作位

　　置。

　?、萁油ㄗ兯傧渖蠑?shù)顯裝置電源，打開起動開關，儀器開始工作，顯示器將顯示延伸長度，在試驗過程中，如發現瀝青細絲浮于水面或沉入槽底時，則加入酒精或食鹽調整水的比重至試樣相過再進行試驗。

　?、薮秊r青試樣拉斷或達到試驗要求時，按一下計值開關，儀器自動計入該試樣的延伸度，三次過后按計值開關，將自動計算三根試樣的

　　平均值。

　　⑦工作結束后，關上電源取出試模，拉出手柄置空檔，將變速箱推回。打開放水閥槽內水放干凈，把水擦干，以防生銹。

　　Fourth,operating procedures:

　?、賂he instrument should be placed horizontally in a room with a temperature of 0°C to 40°C,a relative humidity not exceeding 80%,ａnd no vibration or corrosive gas on the ground with good grounding protection.

　　②Check the water level in the water tank before use.It should meet the requirements of the test operation regulations.With all the function switches off,turn on the power,ａnd check whether the stirring motor and the extension power motor are running well.

　?、跘djust the temperature controller to the required temperature.According to the test requirements and ambient temperature requirements,start the cooling or heating system function switch,ａnd start the stirring motor at the same time.During the test,please use the temperature inside the water tank

　　The meter shall prevail.

　?、躊ull out the handle to turn a corner into neutral position,ａnd then move the gearbox.Place the test mold filled with the sample in the copper cylindrical pin at the extension end of the instrument.Push the handle into the gear to engage the gear and enter the working position.

　　Home.

　?、軸witch on the power of the digital display device on the gearbox,turn on the start switch,ａnd the instrument starts to work.The display will show the extended length.During the test,if it is found that the asphalt filaments float on the water surface or sink to the bottom of the tank,add alcohol or salt Adjust the specific gravity of the water until the sample phase passes before testing.

　　⑥When the asphalt sample is broken or meets the test requirements,press the value switch and the instrument automatically counts the elongation of the sample.After three times,press the value switch to automatically calculate the three samples.

　　average value.

　　后After the work is completed,turn off the power and take out the test mold,pull out the handle to neutral,ａnd push the gearbox back.Open the drain valve slot to drain the water and wipe it dry to prevent rust.

　　低溫瀝青延伸度儀溫度部分操作：

　?、俳油娫?儀表上排顯示測量溫度值,即實際溫度。下排顯示設定溫度值。儀表采用輕觸開關進行參數設定，面板上有四個鍵，SET鍵用于進入溫度設定狀態，和?鍵用于修改數據。按SET鍵3秒，儀表上排顯示“SET”，進入設定值設定狀態，下排顯示原設定值。此時便可對控制溫度進行設定和修改。每按?鍵一次，閃爍的數字加1，當累加值大于9時，自動進位1；每按?鍵一次，閃爍的數字減1，當遞減值小于0時，自動錯位1；

　?、跒r青延伸度儀每按?鍵一次，下排的閃爍數字左移一次。數顯瀝青延伸度儀控制器操作說明1.溫度部分操作:接通電源,儀表上排顯示測量溫度值,即實際溫度。下排顯示設定溫度值。儀表采用輕觸開關進行參數設定，面板上有四個鍵，SET鍵用于進入溫度設定狀態，p、q和t鍵用于修改數據。按SET鍵3秒，儀表上排顯示“SET”，進入設定值設定狀態，下排顯示原設定值。此時便可對控制溫度進行設定和修改。每按p鍵一次，閃爍的數字加1，當累加值大于9時，自動進位1；每按q鍵一次，閃爍的數字減1，當遞減值小于0時，自動錯位1；每按t鍵一次，下排的閃爍數字左移一次。

　?、鄣蜏財?shù)顯瀝青延伸度儀計值部分操作:開機,延時4秒左右,顯示工作界面,有時間、速度、計值1、計值2、計值3及平均值。“循環”鍵為反復鍵,按一次,水泵動作,再按一次,水泵不動作,再按一次,水泵又動作。如此反復。數控低溫數顯瀝青延伸度儀試驗準備好后,按“試驗”鍵,控制器輸出,使電機啟動,開始拉伸試件,用眼觀察,當試件斷裂時,按“計值”鍵一下，以長度1，長度2，長度3。長度3計完后，屏上顯示平均值。試驗完成，此時可按“保存”鍵，保存此次試驗的時間、長度1、2、3及平均值。數據可保存20組，十年時間。如須進行下次試驗，按“試驗”鍵開始新試驗。查詢保存的數據：按“設定”鍵，屏上顯示查詢，每按“→”鍵一次，顯示一組新數據，按試驗先后順序排列，20組數據循環顯示。如系統內無，按“→”鍵，顯示為00年00月00日00時00分，長度1，2，3都為00000。查到一組新數據后，按“清零”鍵，刪除此組數據，一旦數據被刪除，數據將永遠無法找回，請謹慎使用“清零”鍵。在此界面下，按“設定”鍵，進入[日期時間設定界面]。每次查詢數據后必須按“設定”鍵，進入[日期時間設定界面]，再按“設定”鍵進入實驗界面。

　?、艿蜏財?shù)顯瀝青延伸度儀日期時間設定：在實驗界面時，按“設定”鍵，進入查詢，再按“設定”鍵進入[日期時間設定界面]。此時屏上出現一光標，按“→”鍵和“←”鍵可移動光標，把光標移到須改動的數字上，按“+”鍵和“-”鍵，可加減數字，每改變一個數字后，須按“保存”鍵保存，否則修改無效。本系統時間為24小時格式，即下午4點10分應設為16點10分。在此界面下，按“設定”鍵可進入實驗界面

　　Operation of temperature part of low temperature asphalt elongation meter:

　　①Turn on the power,the upper row of the meter displays the measured temperature value,that is,the actual temperature.The lower row shows the set temperature value.The meter uses a touch switch to set the parameters.There are four keys on the panel,the SET key is used to enter the temperature setting state,ａnd the?Key is used to modify the data.Press the SET key for 3 seconds,the upper row of the meter will display“SET”to enter the set value setting state,ａnd the lower row will display the original set value.The control temperature can now be set and modified.Each time the?Key is pressed,the flashing number is increased by 1.When the accumulated value is greater than 9,the flashing number is automatically incremented by 1.When the?Key is pressed once,the flashed number is decreased by 1.

　?、贓ach time the?Key is pressed,the flashing number in the lower row moves to the left once.Digital asphalt elongation meter controller operating instructions 1.Temperature part operation:Turn on the power,the upper row of the meter displays the measured temperature value,that is,the actual temperature.The lower row shows the set temperature value.The meter uses a touch switch to set the parameters.There are four keys on the panel.The SET key is used to enter the temperature setting state,ａnd the p,q,ａnd t keys are used to modify the data.Press the SET key for 3 seconds.The upper display of the meter will display“SET”to enter the set value setting state,ａnd the lower display shows the original set value.The control temperature can now be set and modified.Each time the p key is pressed,the flashing number is increased by 1.When the cumulative value is greater than 9,the flashing number is automatically incremented by 1.When the q key is pressed once,the flashed number is reduced by 1.When the decrement value is less than 0,the position is automatically shifted by 1.Once,the lower flashing number moves to the left once.

　?、跲peration of low temperature digital display asphalt elongation meter:start,delay about 4 seconds,display working interface,time,speed,count 1,count 2,count 3 and average.The"Circulation"key is a repeated key.Press it once to activate the pump.Press it again to prevent the pump from operating.Press it again to activate the pump again.So repeatedly.After the CNC low temperature digital display asphalt elongation test is ready,press the"Test"key,the controller outputs,the motor starts,ａnd the test piece starts to be stretched.Observe with the eyes,when the test piece breaks,press the"Value"key once To length 1,length 2,ａnd length 3.After the length 3 is counted,the average value is displayed on the screen.The test is completed.At this time,you can press the"Save"key to save the time,length 1,2,3 and average of the test.The data can be saved in 20 groups for ten years.If the next test is required,press the"Test"key to start a new test.Query the saved data:Press the"Set"key,ａnd the query will be displayed on the screen.Each time you press the"→"key,a new set of data will be displayed,arranged in the order of the test,ａnd 20 sets of data will be displayed cyclically.If there is nothing in the system,press the"→"key,the display will be 00 00 00 00 00,the length of 1,2,3 are 00000.After finding a new set of data,press the"zero"key to delete this group of data.Once the data is deleted,the data will never be retrieved.Please use the"zero"key with caution.In this interface,press the"Set"key to enter the[Date and Time Setting Interface].After querying the data,you must press the"Set"key to enter the[Date and Time Setting Interface],ａnd then press the"Set"key to enter the experiment interface.

　　④Date and time setting of low temperature digital display asphalt elongation meter:In the experiment interface,press the"Set"key to enter the query,ａnd then press the"Set"key to enter the[Date and time setting interface].At this time,a cursor appears on the screen.Press the"→"and"←"keys to move the cursor.Move the cursor to the number to be changed.Press the"+"and"-"keys to increase or decrease the number.After a number,you must press"Save"to save,otherwise the modification will be invalid.The system time is in a 24-hour format,that is,4:10 pm should be set to 16:10.In this interface,press the"Set"key to enter the experiment interface