騰達試驗儀器廠：

　　QZM錐形磨是檢測儀器，該儀器適用于各種油漆涂料顆粒的研磨，可由原來100微米左右的油漆涂料的顆粒，不超過5次的研磨其顆粒應不大于25微米。

　　QZM conical mill is a testing instrument,which is suitable for the grinding of various paint and coating particles.It can be from the original paint particles of about 100 microns,ａnd the particles should not be more than 25 microns if they are not grinded more than 5 times.

　　QZM錐形磨技術參數：

　　★凸膜與凹膜之間的間隙，可在0.01mm至1mm之間任意調整

　　★凸膜順時針方向轉速180r/min

　　★研磨容量：約50ml

　　★電源：三相交流380V50Hz

　　★外形尺寸：430×250×300mm

　　★質量：約30kg

　　QZM cone mill technical parameters:

　　★The gap between convex film and concave film can be adjusted arbitrarily between 0.01mm and 1mm

　　★Convex film rotation speed 180r/min

　　★Grinding capacity:about 50ml

　　★Power supply:three-phase AC 380V50Hz

　　★Dimensions:430×250×300mm

　　★Quality:about 30kg

　　QZM錐形磨使用說明：

　　★研磨前先將凸磨的兩個研磨面調整到接觸為止，再將需要研磨的油漆涂料倒入凹磨內。

　　★將電源開關（9）接通電源，使電動機（2）通過變速器（3）中的蝸輪，蝸桿及軸帶動凸磨（5）以180轉/分鐘轉速向順時針方向旋轉，此時，油漆涂料被研磨。

　　★研磨后之油漆涂料被刮集到接漆板（10）上則研磨涂料沿此板流出來，在盤（11）上入一玻璃杯，盛放流出來的被研磨之油漆涂料。

　　★長期使用該研磨器，為了保證凸磨與凹磨之間的間隙，其間隙做成可調整的。調整間隙的大小，可通過螺母（7）向順時針方向旋轉，使凸磨（5）既往上移動，而間隙則越來越?。环粗蚰鏁r(shí)針方向旋轉時，間隙則越來越大。

　　★凹磨本身帶有保溫或降溫裝置，通過水嘴可以使一定溫度的水循環流過，使凹磨保持一定的溫度。

　　★變速器（3）內有蝸輪蝸桿轉動，使用3#鈣基脂，其由位至蝸桿的1/3，每三個月加一次油，使其良好潤滑。

　　★凹磨（6）裝卸時可松開旋鈕（12）卻可以取下凹磨，以便進行清洗工作。

　　QZM cone mill instructions:

　　★Before grinding,adjust the two grinding surfaces of the convex grinding to contact,ａnd then pour the paint and coating to be concave into the concave grinding.

　　★Turn on the power switch(9)to make the motor(2)drive the convex mill(5)through the worm gear,worm and shaft in the transmission(3)to rotate clockwise at 180 rpm.The paint is ground.

　　★After the ground paint is scraped and collected on the paint receiving plate(10),the ground paint flows out along this plate,ａnd a glass cup is placed on the plate(11)to hold the ground paint.

　　★The grinder has been used for a long time,in order to ensure the gap between convex grinding and concave grinding,the gap is made adjustable.To adjust the size of the gap,the nut(7)can be rotated clockwise to make the convex grinding wheel(5)move upward,ａnd the gap becomes smaller and smaller;otherwise,the gap becomes larger and larger when rotated counterclockwise.

　　★The concave mill is equipped with a thermal insulation or cooling device.Through a water nozzle,a certain temperature of water can be circulated to keep the concave mill at a certain temperature.

　　★The worm and worm rotate in the transmission(3).It uses 3#calcium base grease,which is 1/3 of the worm.Add oil every three months to make it well lubricated.

　　★The concave mill(6)can be loosened during loading and unloading,but the concave mill can be removed for cleaning.