騰達試驗儀器廠：

　　砂磨分散攪拌多用機是檢測儀器，采用國內外新技術設計的新型產品，該產品集中了攪拌、砂磨、分散多種用途的功能于一體，砂磨分散攪拌多用機用電子恒力高速線路，數字直接顯示轉軸轉速，并配有分散葉輪與砂磨葉盤。能適應實驗室不同的試驗需要，并可根據顯示的轉軸速度直接計算攪拌、分散、砂磨葉片的線速度與物料粘度及化學反應速率之間的關系，為大規模投產提供正確的數據。

　　Sａnd grinding dispersing and stirring multi-purpose machine is a testing instrument.It is a new product designed by new technology at home and abroad.This product integrates the functions of stirring,sａnd grinding and dispersing.It is an electronic constant force for sａnd grinding and dispersing stirring multi-purpose machine.High-speed line,digital display shaft speed directly,ａnd equipped with scattered impeller and sanding disc.It can meet the needs of different experiments in the laboratory,ａnd can directly calculate the relationship between the linear speed of the stirring,dispersing and sanding blades and the material viscosity and chemical reaction rate according to the displayed shaft speed,providing correct data for large-scale production.

　　砂磨分散攪拌多用機技術參數：

　　電動機型號：U400/80-220 400W 220V 100-8000r/min

　　調整范圍：無級恒力調速100-8000r/min

　　攪拌分散葉輪直徑：￠60mm；￠50mm

　　砂磨盤直徑：￠60mm；￠45mm

　　升降行程：250mm

　　外形尺寸：400×450×800mm

　　Technical parameters of sａnd mill dispersing and stirring multi-purpose machine:

　　Motor model:U400/80-220 400W 220V 100-8000r/min

　　Adjustment range:stepless constant force speed 100-8000r/min

　　Stirring and dispersing impeller diameter:￠60mm;￠50mm

　　Sanding disc diameter:￠60mm;￠45mm

　　Lifting stroke:250mm

　　Dimensions:400×450×800mm

　　砂磨分散攪拌多用機維護保養：

　　三角皮帶應長短相等，放入傳動箱內，松緊適當，擰緊滑板螺栓，蓋好上蓋。

　　設備若長期停車不用，須切斷電源，全部擦洗干凈，各潤滑部位注油，主軸和油缸涂油防銹。

　　油箱用46#液壓機油，每半年更換一次并清洗油箱，濾網每月清洗一次，換油后兩三天內清洗一次。

　　分散機轉動部分的齒輪、軸承、滾珠、軸與軸套及油缸，每周注油一次，在使用過程中發現過熱或不正常噪音應及時檢查。

　　如因超載而熱繼電器動作引起停車，則需撳下熱繼電器的“復位”按鈕，方能繼續操作。

　　交流接觸器每半年檢查一次，設備使用一年檢修一次。

　　分散機定期檢查分散機易損件，如軸承、油封等，發現有磨損立即更換。

　　每天必須摸分散機鍋檢查一次，并認真作好摸鍋記錄。

　　當葉片直徑為D時，容器直徑取3.4－3.9D，葉片離地面高度0.5－0.7D，裝料高度取2.4－3D，能取得良好的分散效果。

　　立柱與攪拌軸需定期加潤滑油，一般每班加油一次。

　　傳動三角帶不定期的檢查。

　　Sanding and dispersing mixing multi-purpose machine maintenance:

　　The V-belt should be equal in length and put into the transmission box.It is properly tightened.Tighten the bolts of the slide plate and close the cover.

　　If the equipment is not used for a long period of time,the power must be cut off,all cleaned,the lubrication parts are filled with oil,ａnd the main shaft and oil cylinder are oiled to prevent rust.

　　The fuel tank uses 46#hydraulic oil,which is replaced every six months and the fuel tank is cleaned.The filter is cleaned once a month and once every two to three days after the oil change.

　　Gears,bearings,balls,shafts,bushings and oil cylinders of the rotating part of the dispersing machine are filled with oil once a week.If overheating or abnormal noise is found during use,it should be checked in time.

　　If the thermal relay is shut down due to overload,you need to press the"Reset"button of the thermal relay to continue operation.

　　The AC contactor is checked every six months,ａnd the equipment is overhauled once a year.

　　The dispersing machine regularly inspects the wearing parts of the dispersing machine,such as bearings,oil seals,etc.,ａnd immediately replaces it if found to be worn.

　　The pot of the disperser must be inspected once a day,ａnd the record of the pot should be carefully recorded.

　　When the diameter of the blade is D,the diameter of the container is 3.4-3.9D,the height of the blade from the ground is 0.5-0.7D,ａnd the filling height is 2.4-3D,which can achieve good dispersion effect.

　　Lubricants need to be added regularly to the columns and mixing shafts,usually once every shift.

　　The drive triangle belt is inspected irregularly.

　　砂磨分散攪拌多用機操作規程：

　　開車前

　　檢查分散機油位是否加注到規定位置，低應加至規定油位，高應放至規定位置。

　　檢查三角皮帶松緊是否適當。

　　用手盤動葉輪應轉動靈活，無磨擦聲。

　　檢查各緊固件是否松動及各密封部位有無滲漏現象。

　　開啟分散機主電機，檢查攪拌的旋向是否與設備所規定的方向相同。

　　確認以上檢查工作無誤后方可開車。

　　開車

　　將葉輪放在分散機容器的中間位置，撳下降按鈕，下降到低位置或要求的位置。

　　兩只手柄必須鎖緊后才能開車。

　　開主電機，按操作需要轉速按下按鈕，

　　操作過程中應經常注意電流，如發現超載運轉，應停車檢查原因，采取措施后再繼續運轉分散機。

　　停車

　　先停主電動機，使葉輪全部停止轉動。

　　開分散機上升按鈕，使主軸葉輪上升至容器之上，清洗葉輪。

　　Sａnd mill dispersing and stirring multi-purpose machine operating rules:

　　Before driving

　　Check whether the oil level of the dispersing machine is filled to the specified position.Low should be added to the specified oil level and high should be placed to the specified position.

　　Check that the V-belt is tight.

　　Rotating the impeller by hａnd should be flexible and non-friction.

　　Check whether each fastener is loose and whether there are leaks in each sealing part.

　　Turn on the main motor of the disperser and check whether the rotation direction of the stirring is the same as that specified by the equipment.

　　Make sure that the above inspection work is correct before driving.

　　Drive

　　Place the impeller in the middle position of the disperser container,press the lower button,ａnd lower to the lower position or the required position.

　　Both handles must be locked before driving.

　　Turn on the main motor and press the button at the speed required for operation.

　　Always pay attention to the current during the operation.If overload operation is found,stop the machine to check the cause,ａnd continue to operate the disperser after taking measures.

　　parking

　　Stop the main motor first to stop all the impellers.

　　Turn on the disperser up button to raise the main shaft impeller above the container and clean the impeller.

　　砂磨分散攪拌多用機安裝調試：

　　安裝

　　一般安裝為在水平基礎上打膨脹螺栓即可，有防爆要求需連接電氣柜及防爆操作盒之間的電纜（電纜一般是使用單位電工自行連接，供貨商提供電纜規格）

　　調試

　　啟動升降開關，看升降是否靈活可靠。

　　啟動攪拌開關，轉速調到中速，看是否穩定。

　　Installation and commissioning of sanding dispersing and stirring multi-purpose machine:

　　installation

　　Generally,it is only necessary to install expansion bolts on a horizontal basis.If there is an explosion-proof requirement,you need to connect the cable between the electr