| | | 交叉觸發： The" class=MsoNormal align=left>can be straight forward rising and falling edge or further qualified by pulse width and pulse count. Glitches can be detected using pulse width triggering. Digital domain triggering can use a 8 bit wide digital word or by using the advanced serial trigger( I2C and SPI bus protocols). |
| 
波形發生器： The 100Mpt/S pattern generator has many features not found on other pattern generators. Since it has shared pins with the Logic Analyzer the pattern data can be tri-stated to create bidirectional bus signals. The PG also runs on an independent clock from the logic analyzer, hence you can create a slow signal and analyze the response at a much faster sampling rate. The pattern buffer length is adjustable and can be looped to create complex patterns. The PG can start manually or be synchronized with the MSO trigger inputs. |
| 
高速采集： High speed sampling is key to getting a good capture. The 200MSa single shot sample rate and 60MHz bandwidth will allow you see a great picture of a 60MHz signal in single shot mode and an even faster one if you use RIS mode sampling. |
| 頻譜分析儀： The FFT Spectrum Analyzer has controls for FFT window, FFT type, FFT resolution. The software also supports averaging, memory and plot subtraction. This allows for a whole range of spectral analysis including: Frequency response analysis, Power supply noise analysis, etc... Maximum FFT frequency analysis speed of 100 MHz (with 3dB roll-off at 60MHz). FFT data can be saved to disk and exported to other programs such as Excel, Mathcad, etc.. .. |
|
This example shows use of FFT averaging to identify and reduce noise.
Image 1: Spectral plot of noisy output of an Op Amp circuit. | Image 2: Average after 100 captures of the same circuit. Notice how clear the fundamental ａnd harmonic frequencies are displayed and the random noise is suppressed. |
| Image 3: The noise source was identified and removed. |
| | 波形測量
Standard waveform measurements are included and can be displayed on the screen right next to the traces. |
SPI 和 I2C 解碼
Display and decode SPI and I2C serial bus protocols as well as trigger on them. SPI and I2C signals can also be viewed as timing waveforms and statelist style display. |
| 便捷的操作 - Installation is a snap.
- Make measurements in your first half hour.
- Simple controls make operation intuitive.
- Perform sophisticated operations that you couldn't even dream of doing with a knob based DSO.
- Save default setups to disk for easy recall at a future date.
- Screen shots can be pasted into documents and annotated in your favorite image editing program.
|
| 數據存儲 Data can be saved to disk and reloaded in the future or exported in CSV format for use with other software (Excel, Mathcad, etc...). |
| The windows oscilloscope software takes advantage of your computer's large color screen. Stand-alone oscilloscope display screens represent a compromise at best. Few people would choose a 7" or 9" monitor as the screen for their PC. So why use a small monitor for an oscilloscope? Many people are now using dual monitor PC's - our software will work there also - Imagine having a 30" wide trace window. |
| The speed of your PC does not significantly affect the performance of our instruments All of the high speed acquisition is done with the MSO hardware, the speed of your PC is not a factor. The PC is used for display and for the user interface. If your PC is fast enough and has enough memory to run windows well, it will run our products well also. The Instrument has high speed samplers and buffers. It can acquire at up to 1 GSa/s and stores the data in it's own high speed data buffers. When these buffers are full everything is transferred to the PC. |
| | FONT-SIZE: 12pt">規格 | | 時基 | | | (單次采樣) | 200MSa/s 到 10KSa/s
5nS/sample 到 100uS/sample
50nS/division 到 10mS/division | | (重復采樣) | 2GSa/s 到 1GSa/s
5nS/division to 100nS/division | | 精度 | +/- 0.01% | | 分辨率 | 5ns | | 斜率 | < 5 ns | | 輸入 | | | 輸入 | 1 DSO + 8 Logic Analyzer | | 輸出 | | | 輸出 | 8 Pattern Generator + 1 Trigger out (TTL) | | 波形發生器 | | | 速率 | 100MSa/s...10KSa/s | | 緩存 | Max: 1023 points to 3 points | | Arming control | Sync with MSO trigger, sync with MSO arm and manual start. | | Loop control | Continuous and variable. | | Code generation wizard | SPI, Counter, clock.... | | Output control | Individual channel and sample by sample output enable. | | 模擬量 | | | 帶寬 | 60MHz | | 增益范圍 (每格)
滿刻度 = 8 格 | | Probe | 每格電壓 | 滿刻度電壓 | | 1x | 50mV 到 500mV 每格 | 400mV 到 4V | | 10x | 500mV 到 5V 每格 | 4V 到 40V | | | 輸入電壓 | max input voltage at probe tip depends on probe type (1x and 10x,) | Probe | Continuous | | BNC | ± 20V DC | | 1X probe: | ± 20V DC | | 10X probe: | ± 200V DC | | | 垂直范圍 | 8 格 | | 偏移范圍 | ± 4 divisions | | 偏移分辨率 | 12.5mV | | 耦合方式 | AC and DC | | 電容量 | 1MΩ // 15pF | | DC 精度 | ± 2% | | 數字 | | | 阻抗 | 100K ohm || 2pF | | 電容量 | <500 mv | | .輸入電壓 | +5.5V DC | | 帶寬 | 100MHz | | 門限電壓 | 0.6V 到 1.65V (1.2, 1.5, 1.8,2.5,3.0, 3.3, 5.0V Logic Families) | | 內存 | | | 緩存尺寸 | 1000 點/每通道 | | Trigger | | | 類型 | 上升沿 (調節電平),
下降沿 (調節電平),
脈沖寬度和脈沖計數 8 位寬邏輯分析儀
I2C
SPI | | 外觸發 | 所有的數字通道都能用于外觸發。 | | 外觸發輸入 | 有. | | 模式 | 自動, 普通和單次. | | 自動設置 | 有. | | 范圍 (垂直) | 8 格. | | 分辨率 | 12.5mV | | | | | 軟件 | | | Windows XP/Vista | 有 | | 頻譜分析 / FFT | 有 | | 測量 | 有 | | 物理 | | | 接口 | USB | | 探頭 | One 1x/10x switchable probe is included. | | 連接 | BNC: 2 total: Input and trig-out
Logic Analyzer/Pattern Generator: 8
USB | | 效準點 | Yes | | 電源 | USB 口取電 | | 尺寸 | 4.0" x 2.4" x 0.8" (102mm x 61mm x 20mm)
2.5oz. (70g) (MSO only) 運輸包裝: 9.3" x 6.2" x 2" (240mm x 160mm x 50mm)
運輸重量: 14.3oz. | |
智能制造網APP
智能制造網手機站
智能制造網小程序
智能制造網官微
智能制造網服務號
